C0210/33 Right Rear Wheel Speed Sensor Signal
Diagnostic trouble codes · Vehicles built from Nov 2005
Also covers:
- C0215/34 Left Rear Wheel Speed Sensor Signal
- C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1332/37 Open Circuit in Right Rear Wheel Speed Sensor Circuit
- C1333/38 Open Circuit in Left Rear Wheel Speed Sensor Circuit
DESCRIPTION
Refer to DTC C0200/31 (Click here).| DTC No. |
DTC Detecting Conditions |
Trouble Areas |
| C0210/33 C0215/34 |
When any of following conditions detected:
|
|
| C1273/73 C1274/74 |
Detected only during test mode. |
|
| C1277/77 C1278/78 |
Detected only during test mode. |
|
| C1332/37 C1333/38 |
Open in skid control sensor circuit continues for 0.15 seconds or more. |
|
- HINT:
- DTC C0210/33 and C1332/37 relate to the skid control sensor RH.
- DTC C0215/34 and C1333/38 relate to the skid control sensor LH.
- DTC C0210/33 and C1332/37 relate to the skid control sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the ABS and TRACTION actuator, perform zero point calibration (Click here).
- Check the speed sensor signal in test mode after cleaning or replacement (Click here).
- When replacing the ABS and TRACTION actuator, perform zero point calibration (Click here).
| 1. READ VALUE OF DATA LIST (SKID CONTROL SENSOR) |
Connect the intelligent tester to the DLC3.

Start the engine and drive the vehicle.
Turn the tester on.
Read the wheel speed value using the intelligent tester.Select the following menu items: Chassis / ABS/VSC/TRC / Data List.
Select the item "RR (RL) Wheel Speed" in the DATA LIST and read the value displayed on the intelligent tester.
DATA LIST: ABS/VSC/TRC Item (Display)
Measurement Item / Range (Display)
Normal Condition
RR Wheel Speed
Wheel speed sensor (RR) reading : min.: 0 km/h (0 mph), max.: 300 km/h (186 mph)
Similar to speed indicated on speedometer
RL Wheel Speed
Wheel speed sensor (RL) reading : min.: 0 km/h (0 mph), max.: 300 km/h (186 mph)
Similar to speed indicated on speedometer
Check that there is no significant difference between the speed value displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- OK:
- There is almost no difference in the displayed speed values.
- HINT:
- There is a tolerance of +- 10% in the speedometer indication.
|
|
||||
| OK | |
| 2. PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Perform a TEST MODE inspection and check for DTCs (Click here).
- OK:
- No DTCs output.
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
- Result:
Result
Proceed to
DTC not output
A
DTC output
B
|
|
||||
| A | ||
| ||
| 4. CHECK SKID CONTROL SENSOR |
Visually check the speed sensor for deformation and damage.

- OK:
- No deformation or damage.
- There is no gap between the sensor and rear axle carrier.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR) |
Confirm that the skid control ECU connector and speed sensor connector are properly connected.

Disconnect the skid control ECU connector and the skid control sensor connector.
Inspect both the connector case and the terminal for deformation and corrosion.
- OK:
- No deformation or corrosion.
Measure the resistance.
- Standard Resistance (LH):
Tester Connection
Specified Condition
A39-16 (RL+) - a1-2 (RL+)
Below 1 Ω
A39-15(RL-) - a1-1 (RL-)
Below 1 Ω
- Standard Resistance (RH):
Tester Connection
Specified Condition
A39-24 (RR+) - Z1-2 (RR+)
Below 1 Ω
A39-25 (RR-) - Z1-1 (RR-)
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK SKID CONTROL SENSOR (INPUT VOLTAGE) |
Disconnect the speed sensor connector.

Turn the ignition switch on (IG).
Measure the voltage.
- Standard Voltage:
Tester Connection
Specified Condition
a1-2 (RL+) - Body ground
5.7 to 17.3 V
Z1-2 (RR+) - Body ground
5.7 to 17.3 V
|
|
||||
| OK | |
| 7. RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
- Result:
Result
Proceed to
DTC output
A
DTC not output
B
|
|
||||
| A | |
| 8. REPLACE SKID CONTROL SENSOR |
Replace the skid control sensor.
| NEXT | |
| 9. RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
- Result:
Result
Proceed to
DTC output
A
DTC not output
B
|
|
||||
| A | ||
| ||
