2005-2008 Yaris · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using an intelligent tester.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch on (IG)
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. STOP fuse
  4. IGN fuse
  5. ECM

WIRING DIAGRAM

A159163E01

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. STP signal conditions can be checked using the intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch on (IG).
    3. Turn the tester on.
    4. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.
    5. Check the STP signal when the brake pedal is depressed and released.
      Brake Pedal Operation
      Specified Condition
      Depressed
      STP signal ON
      Released
      STP signal OFF


1. INSPECT STOP LIGHT SWITCH (TERMINAL VOLTAGE)

  1. A148738E02
    Disconnect the stop light switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A13-2 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    A13-3 - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Reconnect the stop light switch connector.



NG
Go to step 4
OK


2. INSPECT STOP LIGHT SWITCH

  1. A115657E11
    Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω

  1. Reinstall the stop light switch.



NG
REPLACE STOP LIGHT SWITCH
OK


3. INSPECT ECM (STP AND ST1 - VOLTAGE)

  1. A112585E15
    Disconnect the ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Brake Pedal Operation
    Specified Condition
    A21-35 (ST1-) - Body ground
    Released
    11 to 14 V
    Depressed
    Below 1.5 V
    A21-36 (STP) - Body ground
    Released
    Below 1.5 V
    Depressed
    11 to 14 V

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

4. INSPECT FUSE (STOP AND IGN FUSES)

  1. A112611E04
    Remove the STOP and IGN fuses from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP fuse
    Always
    Below 1 Ω
    IGN fuse
    Always
    Below 1 Ω

  1. Reinstall the STOP and IGN fuses.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH)


← P0500 Vehicle Speed Sensor "A" (from Nov 2006)P0505 Idle Control System Malfunction (from Nov 2006) →