2005-2008 Yaris · Service Manual ENGINE

P0500 Vehicle Speed Sensor "A"

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.
A079413E13
DTC No.
DTC Detection Conditions
Trouble Areas
P0500
While vehicle being driven, no vehicle speed sensor signal to ECM
(2 trip detection logic)
  1. Open or short in speed signal circuit
  2. Combination meter (Skid control ECU, Vehicle speed sensor)
  3. ECM

WIRING DIAGRAM

A148067E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in speedometer malfunction (Click here).



NG
GO TO MALFUNCTION IN SPEEDOMETER (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT/ Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    Result:
    Result
    Proceed to
    Value displayed on tester and speedometer display not equal
    A
    Value displayed on tester and speedometer display equal
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3. INSPECT COMBINATION METER ASSEMBLY (+S VOLTAGE)

  1. A159448E01
    Disconnect the D1 combination meter connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the combination meter and the body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +S (D1-16) - Body ground
    4.5 to 5.5 V

  1. Reconnect the combination meter connector.



NG
Go to step 5
OK


4. INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

  1. A159449E01
    Shift the transmission gear selector lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    +S (D1-16) - Body ground
    Ignition switch on (IG)
    Turn wheel slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

  1. A106892E04
    Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connections
    Condition
    Specified Conditions
    +S (D1-16) - SPD (A21-8)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Condition
    Specified Conditions
    +S (D1-16) or SPD (A21-8) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0443 Evaporative Emission Control System Purge Control Valve Circuit (from Nov 2006)P0504 Brake Switch "A" / "B" Correlation (from Nov 2006) →