2005-2008 Yaris · Service Manual ENGINE

P0351 Ignition Coil "A" Primary / Secondary Circuit

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil off, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.
A129406E03
DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT (1 to 4) circuit
  3. No. 1 to No. 4 ignition coils
  4. ECM

WIRING DIAGRAM

A159161E01

INSPECTION PROCEDURE

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No. 1 ignition coil circuit.
  3. If DTC P0352 is set, check the No. 2 ignition coil circuit.
  4. If DTC P0353 is set, check the No. 3 ignition coil circuit.
  5. If DTC P0354 is set, check the No. 4 ignition coil circuit.
  6. Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM SIMULATION TEST (SHUFFLE ARRANGEMENT OF IGNITION COILS)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Shuffle arrangement of the ignition coils (among No. 1 to No. 4 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B



B
REPLACE IGNITION COIL
A


2. CHECK IGNITION COIL (POWER SOURCE)

  1. A157860E05
    Disconnect the ignition coil connectors.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C11-1 (+B) - C11-4 (GND)
    Ignition switch on (IG)
    11 to 14 V
    C12-1 (+B) - C12-4 (GND)
    Ignition switch on (IG)
    11 to 14 V
    C13-1 (+B) - C13-4 (GND)
    Ignition switch on (IG)
    11 to 14 V
    C14-1 (+B) - C14-4 (GND)
    Ignition switch on (IG)
    11 to 14 V

  1. Reconnect the ignition coil connectors.



NG
Go to step 5
OK


3. CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)

  1. A157900E05
    Disconnect the ignition coil connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C11-2 (IGF) - C20-81 (IGF1)
    Always
    Below 1 Ω
    C12-2 (IGF) - C20-81 (IGF1)
    Always
    Below 1 Ω
    C13-2 (IGF) - C20-81 (IGF1)
    Always
    Below 1 Ω
    C14-2 (IGF) - C20-81 (IGF1)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C11-2 (IGF) or C20-81 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C12-2 (IGF) or C20-81 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C13-2 (IGF) or C20-81 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C14-2 (IGF) or C20-81 (IGF1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)

  1. A157900E06
    Disconnect the ignition coil connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C11-3 (IGT1) - C20-85 (IGT1)
    Always
    Below 1 Ω
    C12-3 (IGT2) - C20-84 (IGT2)
    Always
    Below 1 Ω
    C13-3 (IGT3) - C20-83 (IGT3)
    Always
    Below 1 Ω
    C14-3 (IGT4) - C20-82 (IGT4)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C11-3 (IGT1) or C20-85 (IGT1) - Body ground
    Always
    10 kΩ or higher
    C12-3 (IGT2) or C20-84 (IGT2) - Body ground
    Always
    10 kΩ or higher
    C13-3 (IGT3) or C20-83 (IGT3) - Body ground
    Always
    10 kΩ or higher
    C14-3 (IGT4) or C20-82 (IGT4) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

5. CHECK HARNESS AND CONNECTOR (IGNITION COIL - BODY GROUND)

  1. A157860E04
    Disconnect the ignition coil connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C11-4 (GND) - Body ground
    Always
    Below 1 Ω
    C12-4 (GND) - Body ground
    Always
    Below 1 Ω
    C13-4 (GND) - Body ground
    Always
    Below 1 Ω
    C14-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ignition coil connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (IGNITION COIL - INTEGRATION RELAY)

  1. A159767E01
    Disconnect the ignition coil connectors.

  1. Remove the integration relay (IG2 relay) from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C11-1 (+B) - 1B-4
    Always
    Below 1 Ω
    C12-1 (+B) - 1B-4
    Always
    Below 1 Ω
    C13-1 (+B) - 1B-4
    Always
    Below 1 Ω
    C14-1 (+B) - 1B-4
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C11-1 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    C12-1 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    C13-1 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    C14-1 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the ignition coil connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT (Click here)


← P0340 Camshaft Position Sensor Circuit Malfunction (+ P0342, P0343) (from Nov 2006)P0365 Camshaft Position Sensor "B" Circuit (Bank 1) (+ P0367, P0368) (from Nov 2006) →