2005-2008 Yaris · Service Manual BODY

Driver Side Power Window does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

  1. When the engine is running or the ignition switch is on (IG), the driver door power window regulator motor is driven by operating the power window regulator master switch. The driver door power window regulator motor has motor, regulator, and ECU functions.

    NOTICE:
    1. The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
    2. When the power window regulator motor assembly (on the driver side) is reinstalled or replaced, the power window control system must be initialized.
    3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
      1. Close the power window by fully pulling up the power window switch and holding it at the AUTO UP position.
      2. Open the power window by fully pushing down the switch.
    4. When the ECU determines that the driver door power window regulator motor has a malfunction, DTC B2311 is set.

    HINT:
    If the pulse sensor built into the power window regulator motor assembly (on the driver side) malfunctions, the power window control system enters fail-safe mode. The remote UP/DOWN and AUTO UP/DOWN functions cannot be operated during fail-safe mode. (However, the power window can be closed by holding the power window switch in the AUTO UP position and opened manually by pushing down the switch).


WIRING DIAGRAM

B111516E01

INSPECTION PROCEDURE


1. CHECK DTC
  1. Check for DTCs.

  1. Connect an intelligent tester to the DLC3.

  1. By following the tester screen display, check whether any DTCs are output.

    Result:
    Display
    Proceed to
    No output
    A
    DTC output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW UP/DOWN)
  1. Perform the active test, using the intelligent tester to generate a control command, and then check the power window operation.

    Power window regulator master switch assembly:
    Item
    Test Details
    Diagnostic Note
    Power Window
    UP/OFF (OFF)
    -
    Power Window
    DOWN/OFF (OFF)
    -

    OK:
    Driver side power window operates normally.

CAUTION:
Be careful to avoid injuries as this test causes parts to move.



NG
Go to step 6
OK


3. READ VALUE OF INTELLIGENT TESTER (MASTER SWITCH)
  1. Check the data list for proper functioning of the power window master switch.

    Power window regulator master switch assembly:
    Item
    Measurement Item/ Display (Range)
    Normal Condition
    Diagnostic Note
    Door P/W Auto SW
    Driver side power window
    AUTO switch signal/ ON or OFF
    ON: Driver side power window AUTO switch operates
    OFF: Driver side power window AUTO switch does not operate
    -
    Door P/W Up SW
    Driver side power window
    UP switch signal/ ON or OFF
    ON: Driver side power window UP switch operates
    OFF: Driver side power window UP switch does not operate
    -
    Door P/W Down SW
    Driver side power window
    DOWN switch signal/ ON or OFF
    ON: Driver side power window DOWN switch operates
    OFF: Driver side power window DOWN switch does not operate
    -

    OK:
    ON (switch operates) appears on screen.



OK
CHECK WHETHER POWER WINDOW REGULATOR MOTOR DRAGS OR SEIZES FOREIGN OBJECTS
NG


4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. B119968E01
    Remove the power window regulator master switch.

  1. Measure the resistance.

    Standard resistance:
    LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    18 (U) - 7 (E) - 1 (AUTO)
    AUTO UP
    Below 1 Ω
    10 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    18 (U) - 7 (E)
    UP
    Below 1 Ω
    10 (D) - 15 (B)
    UP
    Below 1 Ω
    18 (U) - 10 (D) - 15 (B)
    OFF
    Below 1 Ω
    10 (D) - 7 (E)
    DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    DOWN
    Below 1 Ω
    1 (AUTO) - 10 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω
    RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    9 (U) - 7 (E) - 18 (AUTO)
    AUTO UP
    Below 1 Ω
    6 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    9 (U) - 7 (E)
    UP
    Below 1 Ω
    6 (D) - 15 (B)
    UP
    Below 1 Ω
    9 (U) - 6 (D) - 15 (B)
    OFF
    Below 1 Ω
    6 (D) - 7(E)
    DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    DOWN
    Below 1 Ω
    18 (AUTO) - 6 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω

  1. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (SWITCH INPUT POWER SUPPLY)
B119969E01
  1. Disconnect the G1 or F7 power window regulator master switch connector.

  1. Turn the ignition switch to on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    LHD 
    Tester Connection
    Specified Condition
    G1-15 (B) - G1-7 (E)
    10 to 14 V
    RHD 
    Tester Connection
    Specified Condition
    F7-15 (B) - F7-7 (E)
    10 to 14 V

  1. Reconnect the power window regulator master switch connector.



NG
CHECK AND REPLACE POWER SOURCE AND WIRE HARNESS
OK


6. CHECK HARNESS AND CONNECTOR (MASTER SWITCH ASSEMBLY - MOTOR ASSEMBLY (DRIVER SIDE))
B119970E01
  1. Disconnect the G1 or F7 power window regulator master switch connector.

  1. Disconnect the G8 or F8 power window regulator motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    G1-18 (U) - G8-10 (U)
    Below 1 Ω
    G1-10 (D) - G8-7 (D)
    Below 1 Ω
    G1-1 (AUTO) - G8-4 (AUTO)
    Below 1 Ω
    G1-6 (LED+) - G8-5 (LED)
    Below 1 Ω
    RHD 
    Tester Connection
    Specified Condition
    F7-9 (U) - F8-10 (U)
    Below 1 Ω
    F7-6 (D) - F8-7 (D)
    Below 1 Ω
    F7-18 (AUTO) - F8-4 (AUTO)
    Below 1 Ω
    F7-16 (LED+) - F8-5 (LED)
    Below 1 Ω

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (MOTOR INPUT POWER SUPPLY)
B119971E01
  1. Disconnect the G8 or F8 power window regulator motor (driver side) connector.

  1. Turn the ignition switch to on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    LHD 
    Tester Connection
    Specified Condition
    G8-2 (+B) - G8-1 (E)
    10 to 14 V
    RHD 
    Tester Connection
    Specified Condition
    F8-2 (+B) - F8-1 (E)
    10 to 14 V

  1. Reconnect the power window regulator motor connector.



NG
CHECK AND REPLACE POWER SOURCE AND WIRE HARNESS
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)


← Remote Up / Down Function does not Operate (from Aug 2005)Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Aug 2005) →