2005-2008 Yaris · Service Manual BODY

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

  1. When the engine is running or the ignition switch is on (IG) and the window lock switch of the power window regulator master switch assembly is normal, the front passenger door power window regulator motor is driven by operating the front passenger door power window regulator switch.

WIRING DIAGRAM

B133112E01

INSPECTION PROCEDURE


1. READ VALUE OF INTELLIGENT TESTER
  1. Use the data list to check the connection status between the power window regulator motor assembly (driver side) and the main body ECU.

    Main body ECU:
    Item
    Measurement Item/Display (Range)
    Normal Condition
    Diagnostic Note
    Comm D-Door Mtr
    Connection status between power window regulator motor assembly (driver door) and main body ECU
    OK/Stop
    OK: Connection
    Stop: No connection
    -



NG
GO TO DTC CHART
OK


2. CHECK HARNESS AND CONNECTOR (INPUT POWER SUPPLY)

  1. B107969E17
    Disconnect the F1 or G7 power window regulator switch (passenger side) connector.

  1. Turn the ignition switch to on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    LHD 
    Tester Connection
    Specified Condition
    F1-3 - Body ground
    10 to 14 V
    RHD 
    Tester Connection
    Specified Condition
    G7-3 - Body ground
    10 to 14 V

  1. Reconnect the power window regulator switch (passenger side) connector.



NG
INSPECT FUSE AND REPLACE IT IF NECESSARY, OR INSPECT AND REPAIR WIRE HARNESS OR CONNECTOR
OK


3. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE)

  1. B086400E01
    LHD:
    1. Remove the power window regulator motor assembly.

    2. Apply the battery voltage to connector terminals 1 and 2.

      NOTICE:
      Do not apply the battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates counterclockwise

    4. Reinstall the power window regulator motor assembly.

  1. B086401E01
    RHD:
    1. Remove the power window regulator motor assembly.

    2. Apply the battery voltage to connector terminals 1 and 2.

      NOTICE:
      Do not apply the battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates counterclockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates clockwise

    4. Reinstall the power window regulator motor assembly.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE)
OK


4. CHECK HARNESS AND CONNECTOR (SWITCH (PASSENGER SIDE) - MOTOR (PASSENGER SIDE))

  1. Disconnect the F1 or G7 power window regulator switch (passenger side) connector.B111941E07

  1. Disconnect the F4 or G4 power window regulator motor (passenger side) connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    F1-4 - F4-2
    Below 1 Ω
    F1-1 - F4-1
    Below 1 Ω
    F1-4 or F4-2 - Body ground
    10 kΩ or higher
    F1-1 or F4-1 - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    G7-4 - G4-2
    Below 1 Ω
    G7-1 - G4-1
    Below 1 Ω
    G7-4 or G4-2 - Body ground
    10 kΩ or higher
    G7-1 or G4-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY


← Driver Side Power Window does not Operate with Power Window Master Switch (from Aug 2005)Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch (from Aug 2005) →