2005-2008 Yaris · Service Manual BODY

Driver Side Power Window does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

  1. When the engine is running or the ignition switch is on (IG), the driver door power window regulator motor is driven by operating the power window regulator master switch. The driver door power window regulator motor has motor, regulator, and ECU functions.

WIRING DIAGRAM

B111516E01

INSPECTION PROCEDURE


1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. B118062E01
    LHD:
    1. Remove the power window regulator motor assembly.

    2. Apply battery voltage to the regulator motor and check the operation of the regulator motor.

      NOTICE:
      1. Do not apply voltage to any terminals of the motor, except terminal 2, to avoid damaging the pulse sensor inside the motor.
      2. Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door (Click here).

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1, 4 and 10
      Motor gear rotates clockwise
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1 and 7
      Motor gear rotates counterclockwise

    4. Reinstall the power window regulator motor assembly.

  1. B121542E01
    RHD:
    1. Remove the power window regulator motor assembly.

    2. Apply battery voltage to the regulator motor and check the operation of the regulator motor.

      NOTICE:
      1. Do not apply voltage to any terminals of the motor, except terminal 2, to avoid damaging the pulse sensor inside the motor.
      2. Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door (Click here).

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1 and 7
      Motor gear rotates clockwise
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1,4 and 10
      Motor gear rotates counterclockwise

    4. Reinstall the power window regulator motor assembly.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)
OK


2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. B119968E01
    Remove the power window regulator master switch.

  1. Measure the resistance.

    Standard resistance:
    LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    18 (U) - 7 (E) - 1 (AUTO)
    AUTO UP
    Below 1 Ω
    10 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    18 (U) - 7 (E)
    UP
    Below 1 Ω
    10 (D) - 15 (B)
    UP
    Below 1 Ω
    18 (U) - 10 (D) - 15 (B)
    OFF
    Below 1 Ω
    10 (D) - 7 (E)
    DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    DOWN
    Below 1 Ω
    1 (AUTO) - 10 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω
    RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    9 (U) - 7 (E) - 18 (AUTO)
    AUTO UP
    Below 1 Ω
    6 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    9 (U) - 7 (E)
    UP
    Below 1 Ω
    6 (D) - 15 (B)
    UP
    Below 1 Ω
    9 (U) - 6 (D) - 15 (B)
    OFF
    Below 1 Ω
    6 (D) - 7(E)
    DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    DOWN
    Below 1 Ω
    18 (AUTO) - 6 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω

  1. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (MASTER SWITCH ASSEMBLY - MOTOR ASSEMBLY (DRIVER SIDE))
B119970E01
  1. Disconnect the G1 or F7 power window regulator master switch connector.

  1. Disconnect the G8 or F8 power window regulator motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    G1-18 (U) - G8-10 (U)
    Below 1 Ω
    G1-10 (D) - G8-7 (D)
    Below 1 Ω
    G1-1 (AUTO) - G8-4 (AUTO)
    Below 1 Ω
    G1-6 (LED+) - G8-5 (LED)
    Below 1 Ω
    RHD 
    Tester Connection
    Specified Condition
    F7-9 (U) - F8-10 (U)
    Below 1 Ω
    F7-6 (D) - F8-7 (D)
    Below 1 Ω
    F7-18 (AUTO) - F8-4 (AUTO)
    Below 1 Ω
    F7-16 (LED+) - F8-5 (LED)
    Below 1 Ω

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL


← Remote Up / Down Function does not Operate (from Nov 2005)Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Nov 2005) →