2005-2008 Yaris · Service Manual BODY ELECTRICAL

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Aug 2005

CAUTION:
If using a pacemaker, to read the manual of the pacemaker before using the key, as the radio waves of the key may affect the pacemaker.


ENTRY AND START SYSTEM
  1. In addition to conventional mechanical key and wireless door lock control functions, the entry and start system enables door locking/unlocking, steering lock releasing, engine starting and back door opening without the key being operated. The only requirement is that the key is in the user's possession.

    1. This system is controlled by the certification ECU. When the certification ECU detects the presence of the entry and start system in one of the detection areas, it identifies and checks the ID code, and outputs operation signals to the related ECUs in accordance with their functions.
    2. The detection areas are formed by 5 oscillators and 2 antennas (2 door oscillators, back door oscillator (outer), 2 indoor oscillators and 2 door antennas).


DETECTION AREA
B126897E03
  1. Precautions for the entire system:

    1. Be sure to carry the key during inspection of the entry and start system.
    2. As weak radio waves are used to detect the key, the key detection area may decrease, or the key may not be detected correctly in the following situations:
      1. The key battery is depleted.
      2. Any facilities that generate strong radio waves, such as a TV tower, power plant, broadcast station or gas station, are located near the inspection site.
      3. A wireless device, such as a cellular phone, is carried with the key.
      4. The key is in contact with or covered by metal.
      5. Another wireless door lock control function is operated near the vehicle.
      6. The key is located near a device that generates a high voltage or noise.
    1. The key may be difficult to operate for a reason relating to the vehicle body shape.
    2. The key may not be detected correctly if it is near the vehicle's windows, the door handle or center of the bumper, even when it is in the detection area outside the vehicle.
    3. The key may not be detected correctly if it is on the instrument panel, rear package tray or floor, or in the glove box, even when it is in the detection area inside the vehicle.
    4. The key may not operate if the key is held incorrectly.
    5. The entry and start system does not operate under the following conditions:
      1. The entry and start system has been canceled.
      2. The key battery is completely depleted (the indicator does not blink when any of the buttons on the key are pushed).


FUNCTION OF MAIN COMPONENTS
Components
Function
Key
Consists of mechanical key, transmitter for wireless door lock control and transceiver for entry and start system
Certification ECU
Controls entry and start system in accordance with signals from oscillators, various switches, ECUs and key
  1. Judges and certifies ID code from entry door control receiver
  2. Transmits engine immobiliser unset signal to ID code box
  3. Transmits steering unlock signals to steering lock ECU
Main Body ECU
Controls push button start function in accordance with signals from various switches, ECUs and combination meter
  1. Transmits key verification request signal to certification ECU in accordance with ignition switch signal, and turns relays ON and OFF
ID Code Box
Receives steering unlock or engine immobiliser unset signals from certification ECU, certifies them, and transmits unset signals to steering lock ECU or ECM
Outside Door Handle (driver and front passenger doors) (antenna)
Transmits request signals.
Outside Door Handle (driver and front passenger doors) (touch sensor)
Detects when person touches backside of outside door handle
Outside Door Handle (driver and front passenger doors) (lock switch)
Transmits door lock request signals to certification ECU
Door Electrical Key Oscillator (driver and front passenger doors)
Receives request signal from certification ECU, and forms detection area around each door
Indoor Electrical Key Oscillator (front and rear)
Receives request signal from certification ECU, and forms detection area in vehicle interior
Back Door Outer Oscillator
Receives request signal from certification ECU, and forms actuation area around back door.
Door Control Receiver
Receives ID code from key in actuation area and transmits it to certification ECU
Back Door Unlock Switch
Transmits back door unlock request signal to main body ECU
Back Door Lock Switch
Transmits back door lock request signal to certification ECU
Clutch Start Switch
Outputs state of clutch start switch to main body ECU
Wireless Door Lock Buzzer
When certification ECU detects human errors such as those below, it warns driver by sounding wireless door lock buzzer and combination meter buzzer, and flashing entry and start system warning light
Example:
  1. Key is taken outside vehicle
  2. Driver leaves vehicle while engine is still running
Combination Meter
  1. Entry and Start System Warning Light
  2. Buzzer

CONSTRUCTION AND OPERATION

  1. Key
    The key consists of a mechanical key, a transmitter for the wireless door lock remote control, a transceiver for the entry & start system, and a transponder chip for the engine immobiliser control.

    1. The transceiver for the entry & start system receives the signals from the oscillators and returns the ID code to the door control receiver.
    2. The transmitter function for the wireless door lock control has a LOCK switch and an UNLOCK switch.
    3. The mechanical key works for the driver door, but cannot be used to start the engine.
    A total of 4 keys can be registered.
    B128413E01

  2. Oscillator (front LH and RH doors oscillator, front and rear indoor oscillators, back door outer oscillator)
    Each oscillator transmits the request signal it receives from the certification ECU, and forms a key detection area to detect the presence of a key. The detection area formed by each door electrical key oscillator and door electrical key oscillator (back door) is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside handles of the front LH and RH doors or the center of the rear bumper.

    1. The detection area of the front LH and RH door electrical key oscillators are formed by transmitting a request signal every 0.25 seconds while the ignition switch is off and the doors are locked. In this way, the proximity of a key is detected. During entry lock, the detection area is formed with the lock switch ON.
    2. The detection area of the door electrical key oscillator (back door) is formed when the r back door unlock switch is ON.
    3. The detection area of the indoor electrical key oscillator (front and rear) is formed when the driver door is opened or closed, during start ignition, when a warning is activated, or when the lock switch is ON. It is formed twice until the key is verified.
    4. The detection areas of the front and rear room oscillators are formed when the driver door is opened or closed, during start ignition, when a warning is activated, or when the lock switch is ON.


ENTRY FUNCTION OPERATION
  1. The entry and start system has the following functions.

    Function
    Outline
    Mechanical Key
    Operation is same as conventional mechanical key
    Wireless Door Lock Control
    This function remotely locks and unlocks all doors. Operation is same as wireless door lock control system. However, the receiver in certification ECU uses entry door control receiver to control locking and unlocking.
    Entry Illumination
    When person carrying key enters detection area, door enters unlock standby mode and front room light illuminates.
    Entry Unlock
    When key is located in detection area of door oscillator, door can be unlocked by touching backside of outside door handle.
    Entry Lock
    When key is located in detection area of door oscillator and ignition switch is off, door can be locked by pressing lock switch on outside door handle.
    Entry Back Door Open
    When key is in actuation area of door electrical key oscillator (back door), back door can be opened by pressing back door unlock switch.
    Key Lock-in Prevention
    Prevents confinement of key if door is locked using outside door handle while key is inside vehicle.
    Warning
    When any situations below occur, entry and start system causes certification ECU to sound buzzer in combination meter and wireless door lock buzzer, and illuminate key warning light in order to alert driver.
    1. Warning if occupant leaves with key.
    2. Warning if ignition switch is operated while key is outside detection area.
    3. Warning if entry lock is operated while key is inside vehicle.
    4. Warning if key battery is weak.
    Battery Saving
    If key is constantly located within detection area of door oscillator, system maintains periodic communication with key. Therefore, if vehicle remains parked in that state for long time, key battery and vehicle battery could be depleted.
    Key Cancel (Click here)
    Following key functions can be canceled by following certain operations.
    1. Entry Unlock/Lock
    2. Key Lock-in Prevention
    3. Warning
    4. Entry Ignition


WIRELESS DOOR LOCK AND UNLOCK AND BACK DOOR OPEN FUNCTION
Push the LOCK/UNLOCK switch on the key to operate each function.

ENTRY UNLOCK FUNCTION
  1. The detection area is formed by communication between a door electrical key oscillator and door control receiver when the door is locked in order to detect access of the person carrying the key.

  2. When the person carrying the key enters the detection area around the vehicle, the matching of the ID codes for a door electrical key oscillator and key is automatically performed. After the matching is completed, the door enters unlock standby mode.

  3. In unlock standby mode, the antenna built into the outside door handle starts sensing. If the outside door handle is held (the backside of the handle is touched), the door unlock operation is performed. At this time, the hazard warning lights blink twice and the wireless door lock buzzer sounds twice.

  4. If none of the doors are opened within 30 seconds of a door unlock operation, all doors are automatically locked.


ENTRY LOCK FUNCTION
  1. After leaving the vehicle carrying the key, push the lock switch on the outside door handle when all the doors are closed.

  2. The certification ECU determines whether the key is located inside or outside of the cabin based on the information from the door electrical key oscillator and indoor electrical key oscillators. Then matching of the ID codes is performed.

  3. When the matching result shows that the ID codes of the key and indoor electrical key oscillator do not match and the ID codes of the key and door electrical key oscillator match, the door lock function will operate. At this time, the hazard warning lights blink once and the wireless door lock buzzer sounds once.

  4. If the key is located inside the cabin, the door lock function will not operate and the alarm buzzer (beep sound) sounds for 2 seconds.


PREVENTION OF KEY CONFINEMENT FUNCTION
  1. If you attempt to lock the door through keyless operation (move the lock knob to the lock position and then close the door) with the key in the cabin, the system determines that the key is located in the cabin and unlocks the door.

  2. If the back door is closed with the key in the luggage space, the alarm will sound and the back door can be opened only when all the doors are locked in order to prevent key confinement in the vehicle.


ENTRY ILLUMINATION FUNCTION
When a person carrying the key enters the detection area, the door enters unlock standby mode and the room light illuminates.

HINT:
The entry illumination function operates when the key enters the vehicle exterior detection area from outside the detection area. If the key remains in the detection area for 3 seconds or more, the illumination function does not operate.


WARNING FUNCTION
  1. General
    When any of the situations below occur, the entry and start system causes the certification ECU to sound the buzzer in the combination meter and the wireless door lock buzzer, and illuminates the entry and start system warning light to alert the driver.

    Warning Function Operation Condition
    Situation
    Warning if occupant leaves with key.
    A
    Warning if ignition switch is operated while key is outside detection area.
    B
    Warning if entry lock is operated while key is inside vehicle.
    C
    Warning if key battery is weak.
    D
    Warning if clutch start switch malfunction is detected
    E

  2. Situation A
    In this situation, the following control is performed.

    Possible Effects without Warning
    Engine cannot be restarted
    Warning Condition
    Certification ECU gives warning when all following conditions are satisfied
    1. Ignition switch is not off
    2. Any door except driver door is opened and closed
    3. Vehicle speed is 0 km/h (0 mph)
    4. Electrical key is not in vehicle
    Combination Meter
    1. Buzzer
    Warning:
    Sounds once
    Combination Meter
    1. Entry and start system warning light
    Warning: Turns ON
    Warning is stopped when one of following conditions is met
    1. Ignition switch is off
    2. Vehicle speed is above 0 km/h (0 mph)
    3. Electrical key is in vehicle
    Wireless Door Lock Buzzer
    Warning: Sounds 3 times
    Warning is stopped when one of following conditions is met
    1. Ignition switch is off
    2. Vehicle speed is above 0 km/h (0 mph)
    3. Electrical key is in vehicle

  3. Situation B
    In this situation, the following control is performed.

    Possible Effects without Warning
    Confuses the user
    Warning Condition
    Certification ECU gives warning when all following conditions are satisfied
    1. Ignition switch is not off
    2. Electrical key is not in vehicle
    Combination Meter
    1. Buzzer
    Warning:
    Sounds once
    Combination Meter
    1. Entry and start system warning light
    Warning:
    Turns ON for 8 seconds
    Wireless Door Lock Buzzer
    -

  4. Situation C
    In this situation, the following control is performed.

    Possible Effects without Warning
    Vehicle theft
    Warning Condition
    Certification ECU gives warning when all following conditions are satisfied
    1. Ignition switch is off
    2. All doors are closed
    3. Lock switch is "ON"
    4. Electrical key is in vehicle
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Entry and start system warning light
    -
    Wireless Door Lock Buzzer
    Warning:
    Sounds for 2 seconds

  5. Situation D
    In this situation, the following control is performed.

    Possible Effects without Warning
    Entry and start system does not function
    Warning Condition
    Certification ECU gives warning when all following conditions are satisfied
    1. Ignition switch to off after being left in on (IG) for over 20 minutes
    2. Electrical key battery voltage is low
    3. Electrical key is in vehicle
    Combination Meter
    1. Buzzer
    Warning:
    Sounds once
    Combination Meter
    1. Entry and start system warning light
    -
    Wireless Door Lock Buzzer
    -

  6. Situation E (M/T Models Only)
    In this situation, the following control is performed.

    Possible Effects without Warning
    Engine cannot be started
    Warning Condition
    The certification ECU gives warning when all following conditions are satisfied
    1. Ignition switch to off
    2. Driver door is opened after detecting that clutch start switch has been ON for 5 minutes or more
    Warning is stopped when one of following conditions is met
    1. 15 seconds has elapsed
    2. Clutch start switch condition is detected to be normal
    Combination Meter
    1. Buzzer
    -
    Combination Meter
    1. Entry and start system warning light
    -
    Wireless Door Lock Buzzer
    -
    Engine Switch Indicator Light
    Green color blinks in 1-second cycles


BATTERY SAVING

HINT:
Leaving the electrical key close to electrical appliances that emit radio waves could cause the key to accidentally respond, which could cause the key battery to quickly become depleted.

  1. Vehicle Battery Saving Function
    In the entry and start system, signals are emitted outside the vehicle at a prescribed interval (0.25 seconds) when the doors are locked. Therefore, the vehicle battery could be drained if the vehicle remains parked for a long time. For this reason, the controls listed below are affected.

    Condition
    Control
    Both conditions below are met for 5 days:
    1. Electrical key is not in detection area
    2. Touch sensor or lock switch operation is not performed
    Signal transmission interval is extended from 0.25 to 0.75 seconds
    Both conditions below are met for 14 days:
    1. Electrical key is not in detection area
    2. Touch sensor or lock switch operation is not performed
    Automatically deactivates the entry and start system
    Reinstatement Conditions
    1. A wireless door lock control signal (lock or unlock) is input and the ID code matches.
    2. A user, carrying the electrical key, pushes a lock switch on an outside door handle.
    3. A door is locked or unlocked using the mechanical key.

  2. Electrical key Battery and Vehicle Battery Saving Function
    In the entry and start system, if the electrical key is constantly located within the vehicle exterior detection area of the doors, the system maintains periodic communication with the electrical key. Therefore, if the vehicle remains parked in that state for a long time, the electrical key battery and the vehicle battery could be drained. For this reason, if this state continues longer than 10 minutes, the entry and start system automatically becomes deactivated.
    Reinstatement Conditions

    1. A wireless door lock control signal (lock or unlock) is input and the ID code matches.
    2. A user carries the key and pushes a lock switch on an outside handle.
    3. A door is locked or unlocked by the mechanical key.

← SYSTEM DIAGRAM (from Aug 2005)HOW TO PROCEED WITH TROUBLESHOOTING (from Aug 2005) →