2005-2008 Yaris · Service Manual BODY ELECTRICAL

Driver Side Door Entry Lock and Unlock Functions do not Operate

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

Neither the entry lock nor unlock functions operate when: 1) nothing is output from the door electrical key oscillator (driver side), 2) the entry and start system is disabled through customization, or 3) the entire power door lock control system is malfunctioning.

WIRING DIAGRAM

B127159E01

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. By following the tester screen display, check whether any DTCs are output.

    OK:
    No DTC output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART
OK


2. CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION
  1. Check that the manual door lock and unlock function operates normally.

    OK:
    Manual door lock and unlock function operates normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM
OK


3. PERFORM ACTIVE TEST BY INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR (DRIVER SIDE))
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.

    Certification ECU: 
    Item
    Test Details
    Diagnostic Note
    D Transmitter
    Driver side door electrical key oscillator ON / OFF
    -

    OK:
    When key is brought close to door oscillator that is OFF, indicator light on key illuminates.



OK
REPLACE CERTIFICATION ECU ASSEMBLY
NG


4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)

  1. B108060E25
    Disconnect the D60 ECU connector.

  1. Disconnect the S2 or R2 oscillator connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Test Connection
    Specified Condition
    D60-33 (CLG1) - S2-10 (CLG)
    Below 1 Ω
    D60-34 (CG1B) - S2-5 (CLGB)
    Below 1 Ω
    RHD 
    Test Connection
    Specified Condition
    D60-33 (CLG1) - R2-10 (CLG)
    Below 1 Ω
    D60-34 (CG1B) - R2-5 (CLGB)
    Below 1 Ω

  1. Reconnect the ECU connector.

  1. Reconnect the oscillator connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA)

  1. B108040E29
    Disconnect the S2 or R2 oscillator connector.

  1. Disconnect the S1 or R1 antenna connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Test Connection
    Specified Condition
    S2-2 (SGT) - S1-6 (SGT)
    Below 1 Ω
    S2-3 (ANT1) - S1-5 (ANT1)
    Below 1 Ω
    S2-8 (ANT2) - S1-2 (ANT2)
    Below 1 Ω
    S2-9 (TRG-) - S1-1 (TRG-)
    Below 1 Ω
    RHD 
    Test Connection
    Specified Condition
    R2-2 (SGT) - R1-6 (SGT)
    Below 1 Ω
    R2-3 (ANT1) - R1-5 (ANT1)
    Below 1 Ω
    R2-8 (ANT2) - R1-2 (ANT2)
    Below 1 Ω
    R2-9 (TRG-) - R1-1 (TRG-)
    Below 1 Ω

  1. Reconnect the oscillator connector.

  1. Reconnect the antenna connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (+B VOLTAGE AND BODY GROUND)
B127160E01
  1. Disconnect the S2 or R2 oscillator connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    LHD 
    Tester Connection
    Specified Condition
    S2-1 (+B) -S2-7 (GND)
    10 to 14 V
    RHD 
    Tester Connection
    Specified Condition
    R2-1 (+B) - R2-7 (GND)
    10 to 14 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    S2-7 (GND) - body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    R2-7 (GND) - body ground
    10 kΩ or higher

  1. Reconnect the oscillator connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU ASSEMBLY)

  1. B127161E01
    Disconnect the S1 or R1 antenna connector.

  1. Disconnect the D60 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    S1-3 (TRG+) - D60-3 (TSW1)
    Below 1 Ω
    RHD 
    Tester Connection
    Specified Condition
    R1-3 (TRG+) - D60-3 (TSW1)
    Below 1 Ω

  1. Reconnect the antenna connector.

  1. Reconnect the ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK OPERATION OF ELECTRICAL KEY ANTENNA
  1. After replacing the electrical key antenna (driver side) with a normal one, check that the entry lock and unlock functions operate normally.

    OK:
    Entry lock and unlock functions operate normally.



OK
END (ELECTRICAL KEY ANTENNA (DRIVER SIDE) IS DEFECTIVE)
NG


9. CHECK OPERATION OF DOOR ELECTRICAL KEY OSCILLATOR
  1. After replacing the door electrical key oscillator (driver side) with a normal one, check that the entry lock and unlock functions operate normally.

    OK:
    Entry lock and unlock functions operate normally.



NG
REPLACE CERTIFICATION ECU ASSEMBLY
OK

END (DOOR ELECTRICAL KEY OSCILLATOR (DRIVER SIDE) IS DEFECTIVE)


← Front Passenger Side Door Entry Unlock Function does not Operate (from Aug 2005)Front Passenger Side Door Entry Lock and Unlock Functions do not Operate (from Aug 2005) →