2005-2008 Yaris · Service Manual BODY

Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

  1. When the AUTO UP/DOWN dose not function, the power window control system may be in fail-safe mode. If the system has not been initialized after replacement of the driver door power window regulator motor, it also results in the same problem.

WIRING DIAGRAM

B111516E01

INSPECTION PROCEDURE


1. CHECK MANUAL UP / DOWN FUNCTION (DRIVER SIDE)
  1. Check that the manual UP/DOWN functions operate normally.

    OK:
    Manual UP/DOWN functions operate normally.



NG
OTHER PROBLEM
OK


2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. B119968E01
    Remove the power window regulator master switch.

  1. Measure the resistance.

    Standard resistance:
    LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    18 (U) - 7 (E) - 1 (AUTO)
    AUTO UP
    Below 1 Ω
    10 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    18 (U) - 7 (E)
    UP
    Below 1 Ω
    10 (D) - 15 (B)
    UP
    Below 1 Ω
    18 (U) - 10 (D) - 15 (B)
    OFF
    Below 1 Ω
    10 (D) - 7 (E)
    DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    DOWN
    Below 1 Ω
    1 (AUTO) - 10 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω
    RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    9 (U) - 7 (E) - 18 (AUTO)
    AUTO UP
    Below 1 Ω
    6 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    9 (U) - 7 (E)
    UP
    Below 1 Ω
    6 (D) - 15 (B)
    UP
    Below 1 Ω
    9 (U) - 6 (D) - 15 (B)
    OFF
    Below 1 Ω
    6 (D) - 7 (E)
    DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    DOWN
    Below 1 Ω
    18 (AUTO) - 6 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω

  1. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - MOTOR (DRIVER SIDE))

  1. Disconnect the G1 or F7 power window regulator master switch connector.B119970E02

  1. Disconnect the G8 or F8 power window regulator motor (driver side) connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    G1-1 (AUTO) - G8-4 (AUTO)
    Below 1 Ω
    RHD 
    Tester Connection
    Specified Condition
    F7-18 (AUTO) - F8-4 (AUTO)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)


← Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Nov 2005)Power Windows do not Operate at All (from Nov 2005) →