2005-2008 Yaris · Service Manual SECURITIES

B2791 Communication Condition Failure between ECM

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

This DTC is output when the ID code box does not respond to a verification request signal from the ECM.

HINT:
  1. If the ignition switch is turned off immediately after an engine start, this DTC is also detected.
  2. If this DTC is detected, check if any DTCs such as B2799 are output.

DTC No.
DTC Detection Condition
Trouble Area
B2791
ID code box does not respond to verification request signal from ECM
  1. Communication failure between ID code box and ECM
  2. Communication line malfunction
  3. ID code verification failure
  1. Wire harness
  2. ID code box
  3. ECM

WIRING DIAGRAM

B115877E10

INSPECTION PROCEDURE


1. CHECK OPERATION OF ENGINE STARTING
  1. Check that the ignition switch can be turned on (IG) and the engine starts.

    OK:
    Ignition switch can be turned on (IG) and the engine starts.



OK
END (SYSTEM IS NORMAL)
NG


2. CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)

  1. B135495E02
    Disconnect the D58 ID code box connector.

  1. Disconnect the A21 or A32 or A49 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    1KR-FE 
    Tester Connections
    Specified Conditions
    EFII (D58-5) - IMO (A32-40)
    Below 1 Ω
    EFIO (D58-6) - IMI (A32-31)
    Below 1 Ω
    EFII (D58-5) or IMO (A32-40) - Body ground
    10 kΩ or higher
    EFIO (D58-6) or IMI (A32-31) - Body ground
    10 kΩ or higher
    2SZ-FE and 2ZR-FE 
    Tester Connections
    Specified Conditions
    EFII (D58-5) - IMO (A21-10)
    Below 1 Ω
    EFIO (D58-6) - IMI (A21-11)
    Below 1 Ω
    EGND (D58-7) - EOM (A21-9)
    Below 1 Ω
    EFII (D58-5) or IMO (A21-10) - Body ground
    10 kΩ or higher
    EFIO (D58-6) or IMI (A21-11) - Body ground
    10 kΩ or higher
    1ND-TV 
    Tester Connections
    Specified Conditions
    EFII (D58-5) - IMO (A49-4)
    Below 1 Ω
    EFIO (D58-6) - IMI (A49-6)
    Below 1 Ω
    EFII (D58-5) or IMO (A49-4) - Body ground
    10 kΩ or higher
    EFIO (D58-6) or IMI (A49-6) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the ID code box connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK OPERATION OF ID CODE BOX
  1. Clear the DTC (Click here).

  1. After replacing the ID code box with a normal one, check for DTC.

    Result:
    Result
    Proceed to
    B2791 output recurs
    A
    B2791 output does not recurs
    B



B
REPLACE ECM
A

REPLACE ID CODE BOX


← B2790 ID BOX EEPROM Malfunction (from Aug 2005)B2799 Engine Immobiliser System Malfunction (from Aug 2005) →