2005-2008 Yaris · Service Manual SECURITIES

B2799 Engine Immobiliser System Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detects errors in its own communications with the ID code box; 2) the ECM detects errors in the communication lines; or 3) the ECU communication IDs between the ID code box and ECM are different and an engine start is attempted. Before troubleshooting for this DTC, make sure no certification ECU DTCs are present. If present, troubleshoot the certification ECU DTCs first.
DTC No.
DTC Detection Condition
Trouble Area
B2799
One of following conditions is met:
  1. Error in communication between ECM and ID code box
  2. Error in communication lines
  3. Communication IDs are different during communication with ID code box
  1. Wire harness
  2. ID code box
  3. ECM

WIRING DIAGRAM

B115877E10

INSPECTION PROCEDURE


1. CHECK DTC
  1. Clear the DTC (Click here).

  1. Recheck for DTC.

    Result: 
    Result
    Proceed to
    B2799 output recurs
    A
    B2799 output does not recur
    B



B
NORMAL
A


2. RE-REGISTER KEY (ID CODE BOX - ECM)
  1. Clear the DTC (Click here)

  1. Reregister the ID code box and ECM.

  1. Turn the ignition switch on (IG) and check that no DTCs are output.

    Standard:
    No DTC output.



OK
END (PROBLEM HAS BEEN CAUSED BY REGISTRATION FAILURE)
NG


3. CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)

  1. B135495E02
    Disconnect the D58 ID code box connector.

  1. Disconnect the A21 or A32 or A49 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    1KR-FE 
    Tester Connections
    Specified Conditions
    EFII (D58-5) - IMO (A32-40)
    Below 1 Ω
    EFIO (D58-6) - IMI (A32-31)
    Below 1 Ω
    EFII (D58-5) or IMO (A32-40) - Body ground
    10 kΩ or higher
    EFIO (D58-6) or IMI (A32-31) - Body ground
    10 kΩ or higher
    2SZ-FE and 2ZR-FE 
    Tester Connections
    Specified Conditions
    EFII (D58-5) - IMO (A21-10)
    Below 1 Ω
    EFIO (D58-6) - IMI (A21-11)
    Below 1 Ω
    EGND (D58-7) - EOM (A21-9)
    Below 1 Ω
    EFII (D58-5) or IMO (A21-10) - Body ground
    10 kΩ or higher
    EFIO (D58-6) or IMI (A21-11) - Body ground
    10 kΩ or higher
    1ND-TV 
    Tester Connections
    Specified Conditions
    EFII (D58-5) - IMO (A49-4)
    Below 1 Ω
    EFIO (D58-6) - IMI (A49-6)
    Below 1 Ω
    EFII (D58-5) or IMO (A49-4) - Body ground
    10 kΩ or higher
    EFIO (D58-6) or IMI (A49-6) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the ID code box connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK OPERATION OF ID CODE BOX
  1. After replacing the ID code box with a normal one, check that the engine starts.

    HINT:
    After the ECM is replaced, the ECU code and key code must be registered.

    OK:
    Engine starts.



NG
REPLACE ECM
OK

REPLACE ID CODE BOX


← B2791 Communication Condition Failure between ECM (from Aug 2005)ID Code Box Power Source Circuit (from Aug 2005) →