2005-2008 Yaris · Service Manual BODY

Rear Power Window RH does not Operate with Rear Power Window Switch RH

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

If the rear RH side manual UP / DOWN function does not operate, a malfunction may be present in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM

B128294E04

INSPECTION PROCEDURE


1. CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR RH) (POWER SOURCE)
B116300E02
  1. Disconnect the H1 power window regulator switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    H1-3 - Body ground
    Ignition switch ON
    10 to 14 V

  1. Reconnect the power window regulator switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR RH)
B116301E01
  1. Remove the power window regulator switch.

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    3 - 4
    UP
    Below 1 Ω
    1 - 2
    4 - 5
    OFF
    Below 1 Ω
    2 - 3
    4 - 5
    DOWN
    Below 1 Ω

  1. Reinstall the power window regulator switch.



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR RH)
OK


3. CHECK HARNESS AND CONNECTOR (SWITCH (REAR RH) - MOTOR (REAR RH))
B116306E02
  1. Disconnect the H1 power window regulator switch connector.

  1. Disconnect the H2 power window regulator motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    H1-4 - H2-1
    Below 1 Ω
    H1-2 - H2-2
    Below 1 Ω
    H1-4 or H2-1 - Body ground
    10 kΩ or higher
    H1-2 or H2-2 - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH)
B086401E01
  1. Remove the power window regulator motor.

  1. Apply the battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise

  1. Reinstall the power window regulator motor.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH)
OK


5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (REAR RH))
B116307E05
  1. Disconnect the G1 or F7 power window regulator master switch connector.

  1. Disconnect the H1 power window regulator switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    G1-10 (U) - H1-5
    Below 1 Ω
    G1-18 (D) - H1-1
    Below 1 Ω
    G1-10 (U) or H1-5 - Body ground
    10 kΩ or higher
    G1-18 (D) or H1-1 - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    F7-16 (U) - H1-5
    Below 1 Ω
    F7-15 (D) - H1-1
    Below 1 Ω
    F7-16 (U) or H1-5 - Body ground
    10 kΩ or higher
    F7-15 (D) or H1-1 - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the power window regulator switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (REAR RH SWITCH)

  1. Inspect the rear RH switch.

    1. B107909E08
      Remove the power window regulator master switch.

    2. B107910E05
      Measure the resistance of the switch when the switch is operated.

      Standard resistance:
      LHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      1 (E) - 18 (D)
      6 (B) - 10 (U)
      Below 1 Ω
      OFF
      OFF
      1 (E) - 10 (U)
      1 (E) - 18 (D)
      Below 1 Ω
      OFF
      DOWN
      1 (E) - 10 (U)
      6 (B) - 18 (D)
      Below 1 Ω
      ON
      UP
      1 (E) - 18 (D)
      10 kΩ or higher
      6 (B) - 10 (U)
      Below 1 Ω
      ON
      OFF
      10 (U) - 18 (D)
      Below 1 Ω
      ON
      DOWN
      1 (E) - 10 (U)
      10 kΩ or higher
      6 (B) - 18 (D)
      Below 1 Ω
      RHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      9 (E) - 15 (D)
      6 (B) - 16 (U)
      Below 1 Ω
      OFF
      OFF
      9 (E) - 16 (U)
      9 (E) - 15 (D)
      Below 1 Ω
      OFF
      DOWN
      9 (E) - 16 (U)
      6 (B) - 15 (D)
      Below 1 Ω
      ON
      UP
      9 (E) - 15 (D)
      10 kΩ or higher
      6 (B) - 16 (U)
      Below 1 Ω
      ON
      OFF
      16 (U) - 15 (D)
      Below 1 Ω
      ON
      DOWN
      9 (E) - 16 (U)
      10 kΩ or higher
      6 (B) - 15 (D)
      Below 1 Ω

    3. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL


← Rear Power Window LH does not Operate with Rear Power Window Switch LH (from Aug 2005)Power Windows do not Operate at All (from Aug 2005) →