2005-2008 Yaris · Service Manual BODY

Rear Power Window LH does not Operate with Rear Power Window Switch LH

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

If the rear LH side manual UP / DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM

B128294E03

INSPECTION PROCEDURE


1. CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR LH) (POWER SOURCE)
B116300E01
  1. Disconnect the I1 power window regulator switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    I1-3 - Body ground
    Ignition switch ON
    10 to 14 V

  1. Reconnect the power window regulator switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR LH)
B116301E01
  1. Remove the power window regulator switch.

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    3 - 4
    UP
    Below 1 Ω
    4 - 5
    1 - 2
    OFF
    Below 1 Ω
    2 - 3
    4 - 5
    DOWN
    Below 1 Ω

  1. Reinstall the power window regulator switch.



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (REAR LH)
OK


3. CHECK HARNESS AND CONNECTOR (SWITCH (REAR LH) - MOTOR (REAR LH))
B116306E01
  1. Disconnect the I1 power window regulator switch connector.

  1. Disconnect the I2 power window regulator motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    I1-4 - I2-1
    Below 1 Ω
    I1-2 - I2-2
    Below 1 Ω
    I1-4 or I2-1 - Body ground
    10 kΩ or higher
    I1-2 or I2-2 - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH)
B086400E01
  1. Remove the power window regulator motor.

  1. Apply the battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise

  1. Reinstall the power window regulator motor.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH)
OK


5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (REAR LH))
B116307E03
  1. Disconnect the G1 or F7 power window regulator master switch connector.

  1. Disconnect the I1 power window regulator switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    G1-12 (U) - I1-5
    Below 1 Ω
    G1-13 (D) - I1-1
    Below 1 Ω
    G1-12 (U) or I1-5 - Body ground
    10 kΩ or higher
    G1-13 (D) or I1-1 - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    F7-18 (U) - I1-5
    Below 1 Ω
    F7-10 (D) - I1-1
    Below 1 Ω
    F7-18 (U) or I1-5 - Body ground
    10 kΩ or higher
    F7-10 (D) or I1-1 - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the power window regulator switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (REAR LH SWITCH)

  1. Inspect the rear LH switch.

    1. B107909E06
      Remove the power window regulator master switch.

    2. B107910E04
      Measure the resistance of the switch when the switch is operated.

      Standard resistance:
      LHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      1 (E) - 13 (D)
      6 (B) - 12 (U)
      Below 1 Ω
      OFF
      OFF
      1 (E) - 12 (U)
      1 (E) - 13 (D)
      Below 1 Ω
      OFF
      DOWN
      1 (E) - 12 (U)
      6 (B) - 13 (D)
      Below 1 Ω
      ON
      UP
      1 (E) - 13 (D)
      10 kΩ or higher
      6 (B) - 12 (U)
      Below 1 Ω
      ON
      OFF
      12 (U) - 13 (D)
      Below 1 Ω
      ON
      DOWN
      1 (E) - 12 (U)
      10 kΩ or higher
      6 (B) - 13 (D)
      Below 1 Ω
      RHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      9 (E) - 10 (D)
      6 (B) - 18 (U)
      Below 1 Ω
      OFF
      OFF
      9 (E) - 18 (U)
      9 (E) - 10 (D)
      Below 1 Ω
      OFF
      DOWN
      9 (E) - 18 (U)
      6 (B) - 10 (D)
      Below 1 Ω
      ON
      UP
      9 (E) - 10 (D)
      10 kΩ or higher
      6 (B) - 18 (U)
      Below 1 Ω
      ON
      OFF
      18 (U) - 10 (D)
      Below 1 Ω
      ON
      DOWN
      9 (E) - 18 (U)
      10 kΩ or higher
      6 (B) - 10 (D)
      Below 1 Ω

    3. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL


← Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Aug 2005)Rear Power Window RH does not Operate with Rear Power Window Switch RH (from Aug 2005) →