2005-2008 Yaris · Service Manual BODY ELECTRICAL

B2325 LIN Communication Bus Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

This troubleshoot is necessary for w/ double locking system.
DTC B2325 is output when the LIN communication line is abnormal (body ground short) between the power window regulator motor (driver side), double door lock ECU and main body ECU.

CAUTION:
When using the intelligent tester to troubleshoot the LIN communication line: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the tester and vehicle begins.

DTC No.
DTC Detection
Trouble Area
B2325
LIN communication line is abnormal (body ground short) between the main body ECU, power window regulator motor (driver side) and double door lock ECU
  1. Main body ECU
  2. Power window regulator motor (driver side)
  3. Double door lock ECU
  4. Wire harness

WIRING DIAGRAM

B124226E02

INSPECTION PROCEDURE


1. CHECK DTC (DTC B2325)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Main Body ECU / DTC.

  1. Read DTCs.

    Result:
    Display (DTC output)
    Proceed To
    B2325
    A
    No DTC output
    B



B
SYSTEM IS OK
A


2. READ VALUE OF INTELLIGENT TESTER (ECU CONNECTION STATUS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body/ Main Body ECU/ Data List / Comm D-Door Mtr and Comm Double Lock.

  1. Read the indication displayed on the tester.

    Standard:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Comm D-Door Mtr
    Connection status between power window regulator motor assembly (driver door) and main body ECU
    OK/Stop
    OK: Connection
    Stop: No connection
    Comm Double Lock
    Connection status between double door lock ECU and main body ECU
    OK/Stop
    OK: Connection
    Stop: No connection



OK
REPLACE MAIN BODY ECU
NG


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MOTOR (DRIVER SIDE) AND DOUBLE LOCK ECU)

  1. B123841E04
    LHD (w/o Entry and start system):
    1. Disconnect the G8 power window regulator motor and D33 main body ECU connectors.

    2. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      G8-9 (MPX2) - D33-4 (CANP)
      Below 1 Ω
      F8-9 (MPX2) or D33-9 (CANP) - Body ground
      10 kΩ or higher

    3. Reconnect the power window regulator motor and main body ECU connectors.

  1. RHD (w/o Entry and start system):

    1. Disconnect the F8 power window regulator motor, D69 double door lock ECU and D33 main body ECU connectors.

    2. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      F8-9 (MPX2) - D33-4 (CANP)
      Below 1 Ω
      D69-9 (MPX1) - D33-4 (CANP)
      Below 1 Ω
      F8-9 (MPX2) or D69-9 (MPX1) or D33-4 (CANP) - Body ground
      10 kΩ or higher

    3. Reconnect the power window regulator motor, double door lock ECU and main body ECU connectors.

  1. B124227E05
    LHD (w/ Entry and start system):
    1. Disconnect the G8 power window regulator motor and D64 main body ECU connectors.

    2. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      G8-9 (MPX2) - D64-23 (CANP)
      Below 1 Ω
      G8-9 (MPX2) or D64-23 (CANP) - Body ground
      10 kΩ or higher

    3. Reconnect the power window regulator motor and main body ECU connectors.

  1. RHD (w/ Entry and start system):

    1. Disconnect the F8 power window regulator motor, D69 double door lock ECU and D64 main body ECU connectors.

    2. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      F8-9 (MPX2) - D64-23 (CANP)
      Below 1 Ω
      D69-9 (MPX1) - D64-23 (CANP)
      Below 1 Ω
      F8-9 (MPX2) or D69-9 (MPX1) or D64-23 (CANP) - Body ground
      10 kΩ or higher

    3. Reconnect the power window regulator motor, double door lock ECU and main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK DTC (DTC P2325)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Main Body ECU / DTC.

  1. Read DTCs.

    Result:
    Display (DTC output)
    Proceed To
    Only B2325
    A
    B2325 and/or other DTCs
    B

HINT:
If any other DTCs other than B2325 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A

REPLACE MAIN BODY ECU


← B1249 Double Locking ECU Communication Stop (from Aug 2005)All Doors cannot be Locked / Unlocked Simultaneously (from Aug 2005) →