DATA LIST / ACTIVE TEST
System information · Vehicles built from Nov 2005
| DATA LIST |
- HINT:
- By reading the Data List displayed on an intelligent tester, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.
- NOTICE:
- In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.
Warm up the engine.
Turn the ignition switch off.
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Multi-Mode M/T / Data List.
Check the values by referring to the table below.
Items
[Abbreviation]
Measurement Items: Display
Normal Conditions
Diagnostic Notes
MIL Status
[MIL Status]
MIL status:
ON or OFF
ON: MIL comes on
-
Calculated Engine Load
[Calc E/G Load]
Load calculated by ECM:
Min.: 0 %, Max.: 100 %
10 to 25 %: Idling
5 to 20 %: Running without load (2,500 rpm)
-
Engine Coolant Temperature
[Coolant Temp]
Coolant temperature:
Min.: -40°C, Max.: 215°C
75 to 95°C (167 to 203°F):
After engine warmed up
- If value -40 °C (-40 °F): sensor circuit open
- If value 140 °C (284 °F): sensor circuit shorted
Engine Revolution
[Engine Rev]
Engine revolutions per minute:
Min.: 0 rpm, Max.: 16,383.75 rpm
720 to 820 rpm: Idling
If NE signal circuit has a short or open circuit, back-up engine speed data from CAN communication displayed
Vehicle Speed
[Vehicle Spd]
Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
0 km/h (0 mph): Vehicle stationary
Approximately same value as combination meter display
When vehicle speed signal malfunctions, speed value calculated from input revolution signal displayed
Drive Mile after Malfunction
[Driving Mileage]
Accumulated driving mileage since malfunction detection:
Min.: 0 km, Max.: 65,535 km
0 km (0 mile): System normal
Distance driven since occurrence of diagnosis malfunction displayed
Vehicle Speed Signal
[Vehicle Spd Sig]
Vehicle speed signal:
Min.: 0 km/h, Max.: 327.675 km/h
0 km/h (0 mph): Vehicle stationary
When vehicle speed signal malfunctions, speed value calculated from input revolution signal displayed
Input Revolution
[Input Rev.]
Transmission input revolution:
Min.: 0 rpm, Max.: 12,800 rpm
0 rpm: Vehicle stationary
When input revolution signal malfunctions, value calculated from vehicle speed signal displayed
Current Gear Position
[Gear Position]
Current gear position:
N, 1st, 2nd, 3rd, 4th, 5th, R
Actual gear position displayed
-
Backup Engine Speed
[Bacup Engin Spd]
Back-up engine speed:
Min.: 0 rpm, Max.: 8,160 rpm
0 rpm: Engine stopped
0 rpm displayed when malfunctions in CAN communication
Accelerator Pedal Angle
[Accel Pedl Angl]
Accelerator pedal angle:
Min.: 0 %, Max.: 100 %
0 %: Accelerator pedal released
0 % displayed when malfunctions in CAN communication
Theoretical Engine Torque
[Theoretic Torq]
Theoretical engine torque:
Min.: 0 N*m, Max.: 255 N*m
0 N*m: Idling
-
Clutch Position (Current)
[Clutch Pos-Cur]
Current clutch position:
Min.: 0 mm, Max.: 127.998 mm
23.75 mm (0.94 in.) to 42.47 mm (1.67 in.)
Current clutch position displayed
Shift Position (Current)
[Shift Pos-Cur]
Current shift position:
Min.: 0 mm, Max.: 127.998 mm
5.0 mm (0.20 in.) to 34.0 mm (1.34 in.)
Current shift position value displayed (1st, 3rd, 5th, or Neutral, or 2nd, 4th, Reverse)
Select Position (Current)
[Select Pos-Cur]
Current select position:
Min.: 0 mm, Max.: 127.998 mm
14.0 mm (0.55 in.) to 36.0 mm (1.42 in.)
Current select position value displayed (gear shift fork shaft No. 1, No. 2 or No. 3)
Clutch Motor Current MMT
[Clutch Motor]
Clutch motor current:
Min.: -50 A, Max.: 50 A
-25 to 25 A
0 A: When clutch motor not in operation
Shift Motor Current MMT
[Shift Motor]
Shift motor current:
Min.: -50 A, Max.: 50 A
-40 to 40A
0 A: When shift motor not in operation
Select Motor Current MMT
[Select Motor]
Select motor current:
Min.: -50 A, Max.: 50 A
-25 to 25 A
0 A: When select motor not in operation
Gear Position (Current)
[Gear Pos-Cur]
Current gear position:
Min.: 0, Max.: 7
Actual gear position displayed
0=Neutral
7=Reverse
Gear Position (Target)
[Gear Pos-Tar]
Target gear position:
Min.: 0, Max.: 7
When shift lever not operated:
Target gear position equals current gear position
0=Neutral
7=Reverse
Shift Lever Position Judge
[Shift Pos Judge]
Shift lever position:
INVALID POSITION, R, N, E, M
Actual shift lever position displayed
-
Clutch Touch Position
[Clt Touch Pos]
Clutch touch position:
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
-
Clutch Clamp Position
[Clt Clamp Pos]
Clutch clamp position:
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
-
Neutral Position (Shift)
[N Pos (Shift)]
Neutral position (shift position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Median value between [3rd Pos (Shift)] and [4th Pos (Shift)] displayed
Neutral Position (Select)
[N Pos (Sel)]
Neutral position (select position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Median value between [1st Pos (Sel)] and [5th Pos (Sel)] displayed
1st Gear Position (Shift)
[1st Pos (Shift)]
1st gear position (shift position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
- Difference between [1st Pos (Shift)] and [2nd Pos (Shift)] within 17.0 mm (0.67 in.) to 21.5 mm (0.85 in.)
- Difference between [1st Pos (Shift)] and [3rd Pos (Shift)] within 2.5 mm (0.10 in.)
1st Gear Position (Select)
[1st Pos (Sel)]
1st gear position (select position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Difference between [1st Pos (Sel)] and [3rd Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
2nd Gear Position (Shift)
[2nd Pos (Shift)]
2nd gear position (shift position)
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Difference between [1st Pos (Shift)] and [2nd Pos (Shift)] within 17.0 mm (0.67 in.) to 21.5 mm (0.85 in.)
2nd Gear Position (Select)
[2nd Pos (Sel)]
2nd gear position (select position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Difference between [2nd Pos (Sel)] and [4th Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
3rd Gear Position (Shift)
[3rd Pos (Shift)]
3rd gear position (shift position)
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
- Difference between [3rd Pos (Shift)] and [4th Pos (Shift)] within 17.0 mm (0.67 in.) to 21.5 mm (0.85 in.)
- Difference between [5th Pos (Shift)] and [3rd Pos (Shift)] within 2.5 mm (0.10 in.)
3rd Gear Position (Select)
[3rd Pos (Sel)]
3rd gear position (select position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Difference between [3rd Pos (Sel)] and [5th Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
4th Gear Position (Shift)
[4th Pos (Shift)]
4th gear position (shift position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
- Difference between [3rd Pos (Shift)] and [4th Pos (Shift)] within 17.0 mm (0.67 in.) to 21.5 mm (0.85 in.)
- Difference between [R Pos (Shift)] and [4th Pos (Shift)] within 2.5 mm (0.10 in.)
4th Gear Position (Select)
[4th Pos (Sel)]
4th gear position (select position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Difference between [R Pos (Sel)] and [4th Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
5th Gear Position (Shift)
[5th Pos (Shift)]
5th gear position (shift position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
- Difference between [R Pos (Shift)] and [5th Pos (Shift)] within 17.0 mm (0.67 in.) to 21.5 mm (0.85 in.)
- Difference between [3rd Pos (Shift)] and [5th Pos (Shift)] within 2.5 mm (0.10 in.)
5th Gear Position (Select)
[5th Pos (Sel)]
5th gear position (select position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Difference between [5th Pos (Sel)] and [3rd Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
Reverse Gear Pos (Shift)
[R Pos (Shift)]
Reverse gear position (shift position):
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
- Difference between [R Pos (Shift)] and [5th Pos (Shift)] within 17.0 mm (0.67 in.) to 21.5 mm (0.85 in.)
- Difference between [R Pos (Shift)] and [4th Pos (Shift)] within 2.5 mm (0.10 in.)
Reverse Gear Pos (Select)
[R Pos (Sel)]
Reverse gear position (select position)
Min.: 0 mm, Max.: 127.998 mm
Learning value shown
Difference between [R Pos (Sel)] and [4th Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
Cold Condition Judgment
[Cold Condition]
Temperature at engine start:
Min.: -128°C, Max.: 127°C
Lower intake air temperature or engine coolant temperature at 10 seconds after engine start
-
Shift Lever Switch Signal1
[Shift SW Sig1]
Shift lever switch signal (+):
Open (OFF) or Gnd (ON)
Gnd: Shift lever position in (+)
Open: Other than above
LSW1(LSW+) terminal signal of transmission control ECU
Shift Lever Switch Signal2
[Shift SW Sig2]
Shift lever switch signal (R):
Open (OFF) or Gnd (ON)
Gnd: Shift lever position in (R)
Open: Other than above
LSW2 (LSWR) terminal signal of transmission control ECU
Shift Lever Switch Signal3
[Shift SW Sig3]
Shift lever switch signal (M) or (E):
Open (OFF) or Gnd (ON)
Gnd: Shift lever position in (E), (M), (+) or (-)
Open: Shift lever position in (R) or (N)
LSW3 (LSWS) terminal signal of transmission control ECU
Shift Lever Switch Signal4
[Shift SW Sig4]
Shift lever switch signal (N):
Open (OFF) or Gnd (ON)
Gnd: Shift lever position in (N)
Open: Other than above
LSW4 (LSWN) terminal signal of transmission control ECU
Shift Lever Switch Signal5
[Shift SW Sig5]
Shift lever switch signal (-):
Open (OFF) or Gnd (ON)
Gnd: Shift lever position in (-)
Open: Other than above
LSW5 (LSW-) terminal signal of transmission control ECU
Shift Lever Check Signal1
[Shift Chek Sig1]
Check signal of shift lever switch signal 2:
Open (ON) or Gnd (OFF)
Open: Shift lever position in (R)
Gnd: Other than above
LS2C (LSRC) terminal signal of transmission ECU
Reversal signal of LSW2 (LSWR) (ON and OFF reversed)
Shift Lever Check Signal2
[Shift Chek Sig2]
Check signal of shift lever switch signal 3:
Open (ON) or Gnd (OFF)
Open: Shift lever position in (E), (M), (+) or (-)
Gnd: Shift lever position in (R) or (N)
LS3C (LSSC) terminal signal of transmission control ECU
Reversal signal of LSW3 (LSWS) (ON and OFF reversed)
Shift Lever Check Signal3
[Shift Chek Sig3]
Check signal of shift lever switch signal 4:
Open (ON) or Gnd (OFF)
Open: Shift lever position in (N)
Gnd: Other than above
LS4C (LSNC) terminal signal of transmission ECU
Reversal signal of LSW4 (LSWN) (ON and OFF reversed)
T/M Reverse Switch Signal
[T/M R SW Sig]
Transmission reverse switch signal:
Open or Gnd
Gnd: Transmission gear in reverse
Open: Other than above
During malfunctions, indicator shows either ON or OFF continuously, regardless of gear position
Ignition Signal
[Ignition Sig]
Ignition switch signal:
Open (OFF) or +B (ON)
+B: Ignition switch on (IG)
-
Parking Brake Signal
[Pkb Sig]
Parking brake switch signal:
Open (OFF) or Gnd (ON)
Gnd: Parking brake applied
Open: Parking brake released
-
Brake Switch Signal1
[Brake SW Sig1]
Brake switch signal (STP):
Open (OFF) or Gnd (ON)
Gnd: Brake pedal depressed
Open: Brake pedal released
STP terminal signal of transmission control ECU
Brake Switch Signal2
[Brake SW Sig2]
Brake switch signal (ST1-):
Open (OFF) or Gnd (ON)
Open: Brake pedal depressed
Gnd: Brake pedal released
ST1- terminal signal of transmission control ECU
STP Switch Signal
[STP SW Sig]
Brake operation signal:
ON or OFF
ON: Operated
OFF: Not operated
-
STA Switch Signal
[STA SW Sig]
STA signal:
ON or OFF
ON: During cranking
-
Xtest Switch Signal
[Xtest SW Sig]
Diagnosis mode:
Normal or Check
Normal: Diagnosis normal mode
-
Mode Changes
[Mode Changes]
Number of mode changes:
Min.: 0, Max.: 255
-
11: System wake-up control mode
12: Vehicle driving control mode
13: System end control mode
14: System initialization mode
17: Engine starting control mode
20: Fixed gear shift control mode
21: Gear shift control mode
22: Shift lever lock control mode
25: Shut-down control mode
26: Vehicle stationary control mode
27: Vehicle start control mode
Diagnostic Mode
[Diag Mode]
Diagnosis mode:
Min.: 0, Max.: 2
0: Diagnosis normal mode
1: Diagnosis check mode
-
The number of DTCs
[DTC]
Number of detected DTCs (current codes):
Min.: 0, Max.: 255
0: No DTC in transmission control system
-
Possibility of T/M Uplock
[T/M Uplock]
Possibility of transmission up-lock:
No or Yes
No: Initialization and learning complete
Yes: Transmission gear temporarily could not be engaged due to mechanical reasons during gear position learning
Learn-Clutch Standby Point
[Lern-Stby_Pnt]
Clutch actuator standby position learning:
Notexec, Fail or Exec
Exec: Initialization and learning complete
-
Learning-T/M
[Lern-T/M]
Learning T/M system:
Notexec, Fail or Exec
Exec: Initialization and learning complete
-
Learn-Clutch Stopper Point
[Lern-Stppr_Pnt]
Clutch actuator stopper position learning:
Notexec, Fail or Exec
Exec: Initialization and learning complete
-
- If value -40 °C (-40 °F): sensor circuit open
| ACTIVE TEST |
- HINT:
- Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Performing an Active Test as the first step of troubleshooting is one method of shortening diagnostic time.
- Data List can be displayed during Active Tests.
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Multi-Mode M/T / Active Test.
Perform the Active Test by referring to the table below.
Items
Test Details/Vehicle conditions
Diagnosis Notes
Target Gear Position Control
[Test Details]
Target gear position control (Gear position)
N, 1st, 2nd, 3rd, 4th, 5th, R
[Vehicle Conditions]
Ignition switch ON, Engine stopped, Vehicle stationary, Shift lever N position
If shift and select actuator does not shift to the gear indicated, there could be some malfunctions in the following parts.
Shift stroke sensor
Select stroke sensor
Shift and select actuator assembly
AMT relay
Transmission assembly
Transmission control ECU
Target Clutch Control
[Test Details]
Target clutch control
Standby position: Standby
Clamp position: Clamp
[Vehicle Conditions]
Ignition switch ON, Engine stopped, Vehicle stationary, Shift lever N position
If clutch actuator does not operate to the position indicated, there could be some malfunctions in the following parts:
Clutch stroke sensor
Clutch actuator assembly
AMT relay
Clutch release bearing
Clutch release fork
Transmission control ECU