FAIL-SAFE CHART
System information · Vehicles built from Nov 2005
| FAIL-SAFE CHART |
If any of the following codes is recorded, the transmission control ECU enters the fail-safe mode.
DTC No.
Malfunction Areas
Fail-safe Functions
Fail-safe Deactivation Conditions
- P0806
- P0807
- P0808
- P0810
- P0900
- Clutch stroke sensor or its circuit
- Clutch actuator assembly or its circuit
- Gear does not change
- Vehicle does not start moving again after stopping
Either (a) or (b) met: - (a) All of following conditions met:
- Pass condition detected
- Shift lever in N position
- Transmission gear in neutral*
- Vehicle speed less than 6 km/h (3.75 mph)
- (b) Pass condition detected and ignition switch off
- P0807
- P0808
- P0906
- P0907
- P0916
- P0917
- Clutch stroke sensor or its circuit
- Select stroke sensor or its circuit
- Shift stroke sensor or its circuit
- Limit to 3rd gears or lower
Either of (a) or (b) met: - (a) All of the following conditions met:
- Pass condition detected
- Shift lever in N position
- Transmission gear in neutral*
- Vehicle speed less than 6 km/h (3.75 mph)
- (b) Pass condition detected and ignition switch off
- P0905
- P0906
- P0907
- P0909
- P0910
- P0915
- P0916
- P0917
- P0919
- P0920
- Shift stroke sensor or its circuit
- Shift actuator assembly or its circuit
- Select stroke sensor or its circuit
- Select actuator assembly or its circuit
- Gear does not change
- Vehicle does not start moving again after stopping
Either (a) or (b) met: - (a) All of following conditions met:
- Pass condition detected
- Shift lever in N position
- Vehicle speed less than 6 km/h (3.75 mph)
- (b) Pass condition detected and ignition switch off
- P0725
- Engine speed input circuit
- Convert engine revolution signals into CAN communication signals
- No effect
Either (a) or (b) met: - (a) All of following conditions met:
- Pass condition detected
- Actual gear position not in neutral
- Clutch engaged
- (b) Pass condition detected and ignition switch off
- P0500
- P0715
- Vehicle speed sensor or its circuit
- Transmission revolution sensor or its circuit
- Gear does not shift down while driving
- Only possible to drive in 1st or reverse gears after vehicle stops
Either (a) or (b) met: - (a) All of following conditions met:
- Pass condition detected
- Vehicle speed less than 6 km/h (3.73 mph)
- Accelerator pedal released
- Brake pedal depressed
- (b) Pass condition detected and ignition switch off
- P0603
- P0885
- Transmission control ECU
- Clutch actuator, shift actuator, select actuator power source circuit
- Gear does not change
- Engine cannot be started
- Transmission control ECU stops engine when vehicle stops
Pass condition detected and ignition switch off
- P0820
- Shift lever position sensor or its circuit
- Transmission shift main switch or its circuit
- Impossible to enter M-mode
- Gear does not shift to 1st or reverse (and forward or backward gears)
Pass condition detected and ignition switch off
- P0335
- Crankshaft position sensor or its circuit
- Gear does not change
Pass condition detected and ignition switch off
- U0100
- CAN communication signal circuit
- Gear does not change
- Only possible to drive in 1st or reverse gears after vehicle stops
Either (a) or (b) met: - (a) All of following conditions met:
- Pass condition detected
- Vehicle stopped
- Accelerator pedal released
- Brake pedal depressed
- (b) Pass condition detected and ignition switch off
- HINT:
-
*: Transmission gear: Actual transmission gear position
- The transmission control ECU identifies the actual transmission gear position through the signals from the shift stroke sensor and select stroke sensor.
- The transmission control ECU identifies the shift lever position through the signal from the shift lever position sensor.
-
*: Transmission gear: Actual transmission gear position
- P0806