2005-2008 Yaris · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL NO. 1 CLUTCH ACTUATOR BRACKET

  1. D032984
    Install the No. 1 clutch actuator bracket onto the transaxle with the 3 bolts.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }


2. INSTALL MULTI-MODE MANUAL TRANSAXLE ASSEMBLY

  1. C098877
    Align the input shaft with the clutch disc and install the manual transaxle onto the engine.

  1. Install the 7 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }

    NOTICE:
    1. Insert dowel pins into the dowel holes securely so that the end face of the transaxle assembly fits close against the engine assembly before tightening the bolts between the engine and transaxle.
    2. Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle onto the engine with the contact surfaces of the engine and transaxle flat against each other.


3. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

  1. C129933
    Install the engine mounting bracket LH with the 4 bolts.

    Torque:
    :
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


4. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

  1. C129936
    Install the engine mounting insulator and engine mounting bracket with the nut and 6 bolts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }


5. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET

  1. C116856
    Install the engine mounting control bracket with the 4 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


6. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Support the front suspension crossmember with a transmission jack.

  1. A108973E02
    Provisionally install the front suspension crossmember onto the body with the 6 bolts.
    Bolt
    Underhead Length (mm)
    A
    38
    B
    99
    C
    45

  1. By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

    SST
    09670-00011  

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf } for Bolt A
    160 N*m{ 1,631 kgf*cm , 118 ft.*lbf } for Bolt B
    95 N*m{ 969 kgf*cm , 70 ft.*lbf } for Bolt C

    NOTICE:
    1. Insert SST into the datum hole in a vertical orientation.
    2. If SST can not be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.


    A109226E01

  1. C107979E01
    Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1,224 kgf*cm , 89 ft.*lbf }


7. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Coat the spline of the inboard joint with gear oil.

  1. C116899
    Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.

    NOTICE:
    1. Face the cut area of the front drive inboard joint hole snap ring downward.
    2. Do not damage the oil seal.
    3. Do not damage the inboard joint boot.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.


8. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


9. INSTALL FRONT AXLE ASSEMBLY LH
  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.


10. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure as for the RH side.


11. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


12. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure as for the RH side.


13. INSTALL TIE ROD END SUB-ASSEMBLY LH

C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.


14. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the RH side.


15. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 LH

C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.


16. INSTALL FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 RH

HINT:
Use the same procedure as for the RH side.


17. INSTALL SPEED SENSOR FRONT LH

C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.

  1. C125274
    Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.


18. INSTALL SPEED SENSOR FRONT RH

HINT:
Use the same procedure as for the RH side.


19. INSTALL FRONT AXLE SHAFT LH NUT

C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, caulk the axle hub nut.


20. INSTALL FRONT AXLE HUB RH NUT

HINT:
Use the same procedure as for the RH side.


21. INSTALL STARTER ASSEMBLY (for 1.1 kW Type)

A128345
  1. Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the connector.

  1. Connect terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.

  1. A128366
    Install the wire harness bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the harness clamp.


22. INSTALL STARTER ASSEMBLY (for 2.0 kW Type)

A128367
  1. Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the connector.

  1. Connect terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.

  1. A128366
    Install the wire harness bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the harness clamp.


23. CONNECT CONNECTOR
  1. Connect the shift and select motor connectors.

  1. Connect the neutral start switch connector.

  1. Connect the back-up light switch connector.

  1. Connect the transmission revolution sensor connector.

  1. Connect the select stroke sensor connector.

  1. Connect the shift stroke sensor connector.


24. CONNECT WIRE HARNESS

  1. C129943E01
    Connect the wire harness with the bolt.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }


25. INSTALL CLUTCH ACTUATOR ASSEMBLY

D032653
  1. Disconnect the clutch stoke sensor connector and motor connector.

    NOTICE:
    Do not forcibly pull the connectors as this may damage the wire harness.

  1. D032657
    Remove the 3 bolts and clutch actuator assembly.

    NOTICE:
    1. Loosen the bolts slowly, and be careful not to get your fingers caught as the clutch actuator assembly moves due to reaction force from the clutch cover.
    2. Do not drop the removed clutch actuator assembly or impact it in any way.
    3. Do not loosen the nut on the rod tip.


26. INSTALL NO. 1 AIR TUBE

  1. C129934
    Install the No. 1 air tube with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Install the wire harness bracket with the bolt.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the No. 1 air hose with the clamp.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


27. INSTALL NO. 2 AIR HOSE

  1. C129935
    Install the No. 2 air hose with the 2 clamps.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


28. INSTALL BATTERY CARRIER

  1. C106370
    Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }


29. INSTALL BATTERY TRAY

30. INSTALL BATTERY

31. INSTALL BATTERY HOLD DOWN CLAMP

32. INSTALL AIR CLEANER BRACKET

  1. C127612
    Install the air cleaner bracket with the 3 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }


33. INSTALL AIR CLEANER ASSEMBLY

  1. A125745
    Install the air cleaner case sub-assembly with air cleaner inlet with the 3 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }


34. INSTALL NO. 1 AIR CLEANER HOSE
  1. Connect the No. 1 air cleaner hose with the 2 clips.

  1. Connect the 2 fuel hoses.

  1. Connect the No. 1 air cleaner hose with the clamp.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


35. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

A125743
  1. Engage the 4 pins and install engine cover No. 1.


36. INSTALL COWL TOP PANEL OUTER

A126332
  1. Install the cowl top panel outer with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Install the wire harness.


37. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A118801E01
  1. Engage the claws, and install cowl top register duct No. 2.


38. INSTALL WINDSHIELD WIPER MOTOR AND LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


39. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


40. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


41. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


42. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


43. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


44. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


45. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


46. INSPECT HOOD SUB-ASSEMBLY

  1. Check that the clearance measurements are within the standard ranges.

    B118065E01

    Standard:
    Area
    Measurement
    Area
    Measurement
    A
    1.7 to 5.7 mm
    (0.067 to 0.224 in.)
    G
    -1.55 to 2.45 mm
    (-0.061 to 0.096 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    H
    1.75 to 5.75 mm
    (0.067 to 0.226 in.)
    C
    4.45 to 10.45 mm
    (0.175 to 0.411 in.)
    I
    -1.25 to 2.75 mm
    (-0.049 to 0.108 in.)
    D
    -0.95 to 5.05 mm
    (-0.037 to 0.199 in.)
    J
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    E
    7.55 to 13.55 mm
    (0.297 to 0.533 in.)
    K
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    F
    1.65 to 5.65 mm
    (0.065 to 0.222 in.)
    -
    -


47. ADJUST HOOD SUB-ASSEMBLY

  1. B106963
    Loosen the hood side hinge bolts.

  1. Move the hood to adjust the clearance to within the standard range.

  1. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. B106965
    Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.

  1. B106964
    Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


48. ADD TRANSAXLE OIL

49. INSPECT AND ADJUST TRANSAXLE OIL

50. INSTALL ENGINE UNDER COVER

51. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


52. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

C118005E03
  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


53. INSTALL COLUMN HOLE COVER SILENCER SHEET

A116501
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.


54. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


55. PERFORM INITIALIZATION OF MULTI-MODE MANUAL TRANSAXLE ECU
(Click here)

56. PERFORM LEARNING OF MULTI-MODE MANUAL TRANSAXLE SYSTEM
Click here)

57. PERFORM SYNCHRONIZATION POSITION CALIBRATION
(Click here)

58. CHECK ABS SENSOR SIGNAL (w/o VSC)
(Click here)

59. CHECK VSC SENSOR SIGNAL (w/ VSC)
(Click here)

60. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)

61. CHECK FOR TRANSAXLE OIL LEAKAGE
← REMOVAL (from Nov 2005)COMPONENTS (from Nov 2005) →