Multi-Mode Manual Transmission Warning Light Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
The combination meter interprets the multi-mode manual transmission system condition through information from the INDC and INDA circuits, and if necessary, illuminates (blinks) the multi-mode manual transmission warning light and sounds the buzzer.- INDC Terminal Circuit:
The battery voltage is constantly supplied to the INDC circuit. If the INDC circuit is open, the combination meter detects a malfunction in the circuit and illuminates the multi-mode manual transmission warning light. The INDC circuit is used to send the multi-mode manual transmission warning light signal to the combination meter when the ignition switch is off.
- INDA Terminal Circuit:
Power is supplied to the INDA circuit when the ignition switch is on. While the ignition switch is on (IG), the combination meter controls the multi-mode manual transmission warning light ON/OFF condition in accordance with the signal from the INDA circuit. The INDA circuit is used to send the signals for the multi-mode manual transmission warning light and shift position indicator to the combination meter.
| INDA circuit state (at combination meter) |
Normal |
Inconsistent signal input (3 seconds or more) |
Interrupted signal input (3 seconds or more) |
|||
| INDC circuit (at combination meter) |
Normal |
+B short or open |
Normal |
+B short or open |
Normal |
+B short or open |
| Shift position indicator *1 |
ON depends on communication signal |
ON depends on communication signal |
OFF |
OFF |
OFF |
OFF |
| Multi-mode manual transmission warning light |
ON depends on communication signal |
ON depends on communication signal |
ON |
ON |
ON |
ON |
| INDA circuit state (at combination meter) |
Normal |
Inconsistent signal input (3 seconds or more) |
Interrupted signal input (3 seconds or more) |
|||
| INDC circuit state (at combination meter) |
Normal |
+B short or open |
Normal |
+B short or open |
Normal |
+B short or open |
| Shift position indicator *1 |
ON depends on communication signal |
ON depends on communication signal |
OFF |
OFF |
OFF |
OFF |
| Multi-mode manual transmission warning light |
ON depends on communication signal |
ON depends on communication signal |
ON |
ON |
OFF |
ON |
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Check that the multi-mode manual transmission warning light and shift position indicator light come on.
Under normal conditions, the shift position indicator indicates the current gear position while the ignition switch is turned on (IG), and the multi-mode manual transmission warning light comes on for a bulb check for approximately 5 seconds when the ignition switch is turned from off to on (IG).
If the shift position indicator light does not come on, the INDA circuit may be malfunctioning. If the multi-mode manual transmission warning light does not come on, the INDA and/or INDC circuits may be malfunctioning.
- The buzzer built into the combination meter sounds when the following conditions are met:
- The shift lever is in any position except N.
- The driver's door is open.
- Vehicle speed is 10 km/h (6.21 mph) or less.
- Engine speed is 400 rpm or more.
- Check that the multi-mode manual transmission warning light and shift position indicator light come on.
| 1. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU - COMBINATION METER ASSEMBLY) |
Disconnect the transmission control ECU connector.

Disconnect the combination meter connector
Check the resistance.
- Standard resistance:
Tester Connections
Specified Conditions
INDC (D79-29) - BRQ (D1-13)
Below 1 Ω
INDA (D79-31) - TX+ (D1-8)
Below 1 Ω
INDC (D79-29) - Body ground
10 kΩ or higher
INDA (D79-31) - Body ground
10 kΩ or higher
Reconnect the transmission control ECU connector.
Reconnect the combination meter connector.
|
|
||||
| OK | |
| 2. INSPECT COMBINATION METER |
Measure the voltage between the terminal of the combination meter and the body ground.

- Standard voltage:
Tester Connection
Conditions
Specified Conditions
TX+ (D1-8) - Body ground
Ignition switch off
3.64 V or more
TX+ (D1-8) - Body ground
Ignition switch on (IG)
1.44 V or less
BRQ (D1-13) - Body ground
Always
1.44 V or less
|
|
||||
| OK | ||
| ||
