2005-2008 Yaris · Service Manual ENGINE

P0571 Brake Switch "A" Circuit

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The stop light switch has a duplex system (signals STP and ST1-) to store the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:
Normal condition is as shown in the table.
Signal
Brake pedal released
In transition
Brake pedal depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
DTC No.
DTC Detection Condition
Trouble Area
P0571
Both the following conditions are met: (1 trip detection logic)
  1. Ignition switch on (IG)
  2. The following repeatedly occurs 10 times.
    1. STP signal is OFF when the ST1- signal is OFF.
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM


WIRING DIAGRAM

A120354E02

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).


1. CHECK STOP LIGHT OPERATION
  1. Check if the stop lights come on and go off normally when the brake pedal is depressed and released.

    OK:
    The stop lights come on when the brake pedal is depressed.



NG
REPAIR OR REPLACE STOP LIGHT CIRCUIT
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
A072924E17
  1. Remove the stop light switch assembly.

  1. Measure the resistance between each pair of the terminal.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    Switch pin released
    1 - 2
    Below 1 Ω
    Switch pin released
    3 - 4
    10 kΩ or higher
    Switch pin pushed in
    1 - 2
    10 kΩ or higher
    Switch pin pushed in
    3 - 4
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3. CHECK STP AND ST1- SIGNAL
A120355E02
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light SW.

  1. Check the result.

    Standard:
    Brake Pedal
    Specified Condition
    Depressed
    STP Signal ON
    Released
    STP Signal OFF

  1. Measure the voltage between the specified terminals of the ECM connector and the body ground.

    Standard voltage:
    Tester Connection
    Brake pedal
    Specified Condition
    ST1- (A32-16) - Body ground
    Depressed
    Below 1.5 V
    ST1- (A32-16) - Body ground
    Released
    7.5 to 14 V
    STP (A32-38) - Body ground
    Depressed
    7.5 to 14 V
    STP (A32-38) - Body ground
    Released
    Below 1.5 V



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
A120356E02
  1. Disconnect the stop light switch connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    Stop light switch (A13-1) - STP (A32-38)
    Below 1 Ω
    Stop light switch (A13-4) - ST1- (A32-16)
    Below 1 Ω

  1. Reconnect the stop light switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0562 System Voltage Low (+ P0563) (from Aug 2005)P0603 Internal Control Module Keep Alive Memory (KAM) Error (+ P0604, P0605, P0606) (from Aug 2005) →