INSPECTION
Inspection · Vehicles built from Jan 2006
| INSPECT HEATER CONTROL BASE SUB-ASSEMBLY |
![]() ![]() |
Check the heater control base resistance.
Using an ohmmeter, measure the resistance and check the results in accordance with the values in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
2 (L) - 3 (E)
Always
10 kΩ or higher
2 (L) - 4 (B)
A/C switch OFF
10 kΩ or higher
3 (E) - 4 (B)
Always
10 kΩ or higher
2 (L) - 4 (B)
A/C switch ON
Below 1 Ω
5 (ILL+) - 6 (ILL-)
Always
Below 1 Ω
Check the A/C indicator operation.
Connect the positive (+) lead from the battery to terminal 2 (L) and the negative (-) lead to terminal 3 (E).
Push the A/C switch in and check that the indicator lights up.
- Standard:
- Indicator lights up
Check the illumination operation.
Connect the positive (+) lead from the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 6 (ILL-), then check that the bulb illuminates.
- Standard:
- Bulb illuminates
| INSPECT HEATER CONTROL SUB-ASSEMBLY |
![]() ![]() |
Check the heater control resistance.
Using an ohmmeter, measure the resistance and check the results in accordance with the values in the table below.
- Standard resistance:
Switch Position
Tester Connection
Specified Condition
OFF
ALL - 5 (E)
10 kΩ or higher
LO
9 (LO) - 5 (E)
Below 1 Ω
LO - M1
9 (LO) - 5 (E) - 7 (M1)
Below 1 Ω
M1
9 (LO) - 5 (E) - 7 (M1)
Below 1 Ω
M1 - M2
9 (LO) - 5 (E) - 7 (M1) - 6 (M2)
Below 1 Ω
M2
9 (LO) - 5 (E) - 6 (M2)
Below 1 Ω
M2 - HI
9 (LO) - 5 (E) - 6 (M2) - 10 (HI)
Below 1 Ω
HI
9 (LO) - 5 (E) - 10 (HI)
Below 1 Ω
Check the illumination operation.
Connect the positive (+) lead from the battery to terminal 2 (ILL+) and the negative (-) lead to terminal 1 (ILL-), then check that the bulb illuminates.
- Standard:
- Bulb illuminates
| INSPECT NO. 3 HEATER CONTROL KNOB |
![]() ![]() |
Check the No. 3 heater control knob resistance.
Using an ohmmeter, measure the resistance and check the results in accordance with the values in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
2 (RrDEF) - 1 (E)
Rr. DEF switch OFF
10 kΩ or higher
2 (RrDEF) - 1 (E)
Rr. DEF switch ON
Below 1 Ω
3 (IG) - 6 (MAX HOT)
Except MAX HOT
10 kΩ or higher
3 (IG) - 6 (MAX HOT)
MAX HOT
Below 1 Ω
4 (ILL-) - 5 (ILL+)
Always
Below 1 Ω
7 (V/B) - 8 (SG)
Always
Below 1 Ω
Check the Rr. DEF indicator operation.
Connect the positive (+) lead from the battery to terminal 3 (IG) and the negative (-) lead to terminal 1 (E).
Push the Rr. DEF switch in and check that the indicator lights up.
- Standard:
- Indicator lights up
Check the illumination operation.
Connect the positive (+) lead from the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 4 (ILL-), then check that the bulb illuminates.
- Standard:
- Bulb illuminates
Check the No. 3 heater control knob resistance.

(for Boost vent)Using an ohmmeter, measure the resistance variation between connector terminals 7 (V/B) and 8 (SG) when the dial is turned as shown in the illustration.
- Standard:
- Varies as shown in the illustration



