2005-2008 Yaris · Service Manual ENGINE

P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

HINT:
This ETC (Electrical Throttle Control System) does not use a throttle cable.

The Throttle Position (TP) sensor is mounted on the throttle body, and detects the opening angle of the throttle valve.
The TP sensor has two sensor circuits which each transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V. The VTA1 sensor signal voltage varies in proportion to the throttle valve opening angle, and is transmitted to the VTA terminals of the ECM.
As the valve closes, the VTA1 sensor output voltage decreases, and as the valve opens, the VTA1 sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals (VTA1 and VTA2) and controls the throttle actuator in response to driver inputs.
A113732E01
DTC No.
DTC Detection Condition
Trouble Area
P0122
Output voltage of VTA1 0.2 V or less for 0.14 seconds or more
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  1. Open or short in VTA1 circuit
  1. Open in VC circuit
  1. ECM
P0123
Output voltage of VTA1 4.6 V or more
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  1. Open in VTA1 circuit
  1. Open in E2 circuit
  1. Short between VC and VTA1 circuits
  1. ECM
P0222
Output voltage of VTA2 0.156 V or less when engine speed is 1,200 rpm or more for 0.14 seconds or more
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  1. Open or short in VTA2 circuit
  1. Open in VC circuit
  1. ECM
P0223
Output voltage of VTA2 4.883 V or more
(1 trip detection logic)
  1. TP sensor (built into throttle body)
  1. Open in VTA2 circuit
  1. Open in E2 circuit
  1. Short between VC and VTA2 circuits
  1. ECM

HINT:
  1. Detection is always being performed for P0122, P0123 and P0223 when the ignition switch is on (IG) or the engine is running.
  2. Detection for P0222 is performed when the engine speed is 1,200 rpm or greater.


WIRING DIAGRAM

A116149E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (THROTTLE BODY - ECM)
A116148E01
  1. Disconnect the throttle body connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VC (C39-3) - VC (C33-54)
    Below 1 Ω
    VTA (C39-6) - VTA1 (C33-21)
    Below 1 Ω
    VTA2 (C39-5) - VTA2 (C33-37)
    Below 1 Ω
    E2 (C39-2) - ETA (C33-39)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VC (C39-3) or VC (C33-54) - Body ground
    10 kΩ or higher
    VTA (C39-6) or VTA1 (C33-21) - Body ground
    10 kΩ or higher
    VTA2 (C39-5) or VTA2 (C33-37) - Body ground
    10 kΩ or higher
    E2 (C39-2) or ETA (C33-39) - Body ground
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK TERMINAL VOLTAGE (THROTTLE BODY CONNECTOR)
A104100E03
  1. Disconnect the throttle body connector.

  1. Measure the voltage between the terminals of the throttle body connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VC (C39-3) - E2 (C39-2)
    4.5 to 5.5 V

  1. Reconnect the throttle body connector.



NG
REPLACE ECM
OK


3. REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly.

  1. Perform electronic throttle learning (Click here).


NEXT

END


← P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (+ P0221) (from Aug 2005)P0125 Insufficient Coolant Temperature for Closed Loop Fuel Control (from Aug 2005) →