2005-2008 Yaris · Service Manual ENGINE

P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

HINT:
This ETC (Electrical Throttle Control System) does not use a throttle cable.

The Throttle Position (TP) sensor is mounted on the throttle body, and detects the opening angle of the throttle valve.
The TP sensor has two sensor circuits which each transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V. The VTA1 sensor signal voltage varies in proportion to the throttle valve opening angle, and is transmitted to the VTA terminals of the ECM.
As the valve closes, the VTA1 sensor output voltage decreases, and as the valve opens, the VTA1 sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals (VTA1 and VTA2) and controls the throttle actuator in response to driver inputs.
A113732E01
DTC No.
DTC Detection Condition
Trouble Area
P0121
  1. A temporary malfunction is detected if the difference in output between sensors 1 and 2 is 6.3 % or more. Following this temporary detection, if there is a 9 % or more difference between sensor 1 and assumed throttle angle with Manifold Absolute Pressure (MAP) sensor, a malfunction is detected. (1 trip detection logic)
  2. ETCS throttle opener position error
  1. Throttle Position (TP) sensor (built into throttle body)
  2. ECM
P0221
  1. A temporary malfunction is detected if the difference in output between sensors 1 and 2 is 6.3 % or more. Following this temporary detection, if there is a 9 % or more difference between sensor 2 and assumed throttle angle with MAP sensor, a malfunction is detected. (1 trip detection logic)
  1. TP sensor (built into throttle body)
  2. ECM

HINT:
DTC P0121 and P0221 are detected when the vehicle is driven in the city at 30 to 50 km/h (19 to 31 mph) for 5 minutes.


WIRING DIAGRAM

A116149E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (THROTTLE BODY - ECM)
A116148E01
  1. Disconnect the throttle body connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VC (C39-3) - VC (C33-54)
    Below 1 Ω
    VTA (C39-6) - VTA1 (C33-21)
    Below 1 Ω
    VTA2 (C39-5) - VTA2 (C33-37)
    Below 1 Ω
    E2 (C39-2) - ETA (C33-39)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VC (C39-3) or VC (C33-54) - Body ground
    10 kΩ or higher
    VTA (C39-6) or VTA1 (C33-21) - Body ground
    10 kΩ or higher
    VTA2 (C39-5) or VTA2 (C33-37) - Body ground
    10 kΩ or higher
    E2 (C39-2) or ETA (C33-39) - Body ground
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. REPLACE THROTTLE BODY ASSEMBLY
  1. Replace throttle body assembly.

  1. Perform electronic throttle learning (Click here).


NEXT

END


← P0117 Engine Coolant Temperature Circuit Low Input (+ P0118) (from Aug 2005)P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input (+ P0123, P0222, P0223) (from Aug 2005) →