2005-2008 Yaris · Service Manual ENGINE

P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.
The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and malfunctions of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal which indicates the actual accelerator pedal opening angle and is used for engine control, and the VPA2 is a signal which indicates the information about the opening angle and is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.

A112620E01
DTC No.
DTC Detection Condition
Trouble Area
P2138
The difference in output between accelerator pedal position sensors 1 and 2 is outside the threshold range. (1 trip detection logic)
Accelerator pedal

HINT:
Detection for P2138 is performed when the ignition switch is on (IG) or engine running.


WIRING DIAGRAM

A112573E06

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A120358E01
    Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    VCPA (A32-11) - VCPA (A20-4)
    Below 1 Ω
    VPA (A32-10) - VPA (A20-6)
    Below 1 Ω
    EPA (A32-9) - EPA (A20-5)
    Below 1 Ω
    VCP2 (A32-19) - VCP2 (A20-1)
    Below 1 Ω
    VPA2 (A32-18) - VPA2 (A20-3)
    Below 1 Ω
    EPA2 (A32-17) - EPA2 (A20-2)
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    VCPA (A32-11) or VCPA (A20-4) - Body ground
    10 kΩ or higher
    VPA (A32-10) or VPA (A20-6) - Body ground
    10 kΩ or higher
    EPA (A32-9) or EPA (A20-5) - Body ground
    10 kΩ or higher
    VCP2 (A32-19) or VCP2 (A20-1) - Body ground
    10 kΩ or higher
    VPA2 (A32-18) or VPA2 (A20-3) - Body ground
    10 kΩ or higher
    EPA2 (A32-17) or EPA2 (A20-2) - Body ground
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ACCELERATOR PEDAL ASSEMBLY


← P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input (+ P2123, P2127, P2128) (from Aug 2005)U0101 Lost Communication with TCM (from Nov 2005) →