2005-2008 Yaris · Service Manual ENGINE

P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.
The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and malfunctions of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal which indicates the actual accelerator pedal opening angle and is used for engine control, and the VPA2 is a signal which indicates the information about the opening angle and is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.

A112620E01
DTC No.
DTC Detection Condition
(All of following are 1 trip detection logic)
Trouble Area
P2122
VPA is 0.7 V or less for 0.5 seconds or more when VPA2 output indicates accelerator pedal is depressed
  1. Accelerator pedal
  2. Open in VCPA circuit
  3. VPA circuit open or ground short
  4. ECM
P2123
  1. Condition (a) continues for 2.0 seconds or more:
    1. VPA is 4.8 V or more
  1. Accelerator pedal
  2. Open in EPA circuit
  3. Short in VCPA circuit
  4. ECM
P2127
VPA2 is 0.65 V or less for 0.5 seconds or more when VPA output indicates accelerator pedal is depressd
  1. Accelerator pedal
  2. Open in VCP2 circuit
  3. VPA2 circuit open or ground short
  4. ECM
P2128
VPA2 is 4.03 V or more for 2.0 seconds or more
  1. Accelerator pedal
  2. Open in EPA2 circuit
  3. Short in VCPA2 circuit
  4. ECM

HINT:
Detection for P2122, P2123, P2127 and P2128 are performed when the ignition switch is on (IG) or engine running.


WIRING DIAGRAM

A112573E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A120358E01
    Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    VCPA (A32-11) - VCPA (A20-4)
    Below 1 Ω
    VPA (A32-10) - VPA (A20-6)
    Below 1 Ω
    EPA (A32-9) - EPA (A20-5)
    Below 1 Ω
    VCP2 (A32-19) - VCP2 (A20-1)
    Below 1 Ω
    VPA2 (A32-18) - VPA2 (A20-3)
    Below 1 Ω
    EPA2 (A32-17) - EPA2 (A20-2)
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    VCPA (A32-11) or VCPA (A20-4) - Body ground
    10 kΩ or higher
    VPA (A32-10) or VPA (A20-6) - Body ground
    10 kΩ or higher
    EPA (A32-9) or EPA (A20-5) - Body ground
    10 kΩ or higher
    VCP2 (A32-19) or VCP2 (A20-1) - Body ground
    10 kΩ or higher
    VPA2 (A32-18) or VPA2 (A20-3) - Body ground
    10 kΩ or higher
    EPA2 (A32-17) or EPA2 (A20-2) - Body ground
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK TERMINAL VOLTAGE (ACCELERATOR PEDAL POSITION SENSOR CONNECTOR)

  1. A109192E03
    Disconnect the accelerator pedal position sensor connector.

  1. Measure the voltage between the terminals of the accelerator pedal position sensor connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VCP2 - EPA2
    4.5 to 5.5 V
    VCPA - EPA
    4.5 to 5.5 V

  1. Reconnect the accelerator pedal position sensor connector.

  1. Clear the DTC.



NG
REPLACE ECM
OK

REPLACE ACCELERATOR PEDAL ASSEMBLY


← P2119 Throttle Actuator Control Throttle Body Range / Performance (from Aug 2005)P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation (from Aug 2005) →