2005-2008 Yaris · Service Manual TRANSMISSION

P0820 Gear Lever "X-Y" Position Sensor Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The transmission control ECU detects the shift lever position using the shift lever position sensor. The shift lever position sensor has two functions; detection and monitoring.
The shift lever position sensor consists of a Link 1 circuit that detects the shift lever positions, R, N, E and M, and a Link 2 circuit that detects the [+] and [-] positions. The circuits are connected to the shift lever via the respective links. The contact switches (6-contact switch for Link 1, and 2-contact switch for Link 2) of the circuits turn on and off in accordance with the fore-aft movement of the shift lever. The transmission control ECU detects the present shift lever position in accordance with the ON/OFF status of these contact switches. The transmission shift main switch detects the side-to-side movement of the shift lever. It turns off when the shift lever is in the R, N, or E position, and turns on in the M, [+], or [-] position.
The shift lever position sensor and the transmission shift main switch convert the shift lever position into electric signals and output them to the transmission control ECU. The transmission control ECU detects the present shift lever position from these signals and operates the actuators to change the gear position.
Contact Points
Shift Lever Position
R
N
E
M
-
+
Link 1
LSRC
OFF
ON
ON
ON
ON
ON
LSWR
ON
OFF
OFF
OFF
OFF
OFF
LSSC
ON
ON
OFF
OFF
OFF
OFF
LSWS
OFF
OFF
ON
ON
ON
ON
LSNC
ON
OFF
ON
ON
ON
ON
LSWN
OFF
ON
OFF
OFF
OFF
OFF
Link 2
LSW-
OFF
OFF
OFF
OFF
ON
OFF
LSW+
OFF
OFF
OFF
OFF
OFF
ON
Transmission Shift Main Switch
OFF
OFF
OFF
ON
ON
ON

HINT:
The monitor runs when the shift lever is moved through each position (N, R, E, M, - and +).

C129094E01
C111592E01
C111593E01
DTC No.
DTC Detection Conditions
Trouble Areas
P0820
The transmission control ECU detects one of the following conditions:
(1 trip detection logic)
  1. Both the LSW4 (LSWN) signal and the LS4C (LSNC) signal are OFF for 5.0 seconds
  2. Both the LSW4 (LSWN) signal and the LS4C (LSNC) signal are ON for 30.0 seconds
  3. The condition that both the LSW4 (LSWN) signal and the LS4C (LSNC) signal are ON for 15.0 seconds or more is detected 5 times
  1. Shift lever position sensor
  2. Open or short in shift lever position signal circuit
  3. Transmission control ECU
P0820
The transmission control ECU detects one of the following conditions:
(1 trip detection logic)
  1. Both the LSW3 (LSWS) signal and the LS3C (LSSC) signal are OFF for 5.0 seconds
  2. Both the LSW3 (LSWS) signal and the LS3C (LSSC) signal are ON for 30.0 seconds
  3. The condition that both the LSW3 (LSWS) signal and the LS3C (LSSC) signal are ON for 15.0 seconds or more is detected 5 times
  1. Shift level position sensor
  2. Open or short in shift lever position signal circuit
  3. Transmission control ECU
P0820
The transmission control ECU detects one of the following conditions:
(1 trip detection logic)
  1. Both the LSW2 (LSWR) signal and the LS2C (LSRC) signal are OFF for 5.0 seconds
  2. Both the LSW2 (LSWR) signal and the LS2C (LSRC) signal are ON for 30.0 seconds
  3. The condition that both the LSW2 (LSWR) signal and the LS2C (LSRC) signal are ON for 15.0 seconds or more is detected 5 times
  1. Shift level position sensor
  2. Open or short in shift lever position signal circuit
  3. Transmission control ECU
P0820
The transmission control ECU detects the following conditions simultaneously:
(1 trip detection logic)
  1. Shift lever position is N or R
  2. LSW1 (LSW+) signal or LSW5 (LSW-) signal is ON for 1.0 second
  1. Shift level position sensor
  2. Short in shift lever position signal circuit
  3. Transmission control ECU

WIRING DIAGRAM

C110756E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and the tester ON.

  1. Select the following menu items: Powertrain / Multi-Mode M/T / Data List / Shift Lever Switch Signal 1 - 5, and Shift Lever Check Signal 1 - 3.

  1. Check that the normal condition specified in the following table is shown on the display when moving the shift lever to each position R, N, E, M, +, and -.

    Items
    [Abbreviation]
    Measurement Items: Display
    Normal Conditions
    Diagnostic Notes
    Shift Lever Switch Signal1
    [Shift SW Sig1]
    Shift lever switch signal (+):
    Open (OFF) or Gnd (ON)
    Gnd: Shift lever position in (+)
    Open: Other than above
    LSW1 (LSW+) terminal signal of transmission control ECU
    Shift Lever Switch Signal2
    [Shift SW Sig2]
    Shift lever switch signal (R):
    Open (OFF) or Gnd (ON)
    Gnd: Shift lever position in (R)
    Open: Other than above
    LSW2 (LSWR) terminal signal of transmission control ECU
    Shift Lever Switch Signal3
    [Shift SW Sig3]
    Shift lever switch signal (M) or (E):
    Open (OFF) or Gnd (ON)
    Gnd: Shift lever position in (E), (M), (+) or (-)
    Open: Shift lever position in (R) or (N)
    LSW3 (LSWS) terminal signal of transmission control ECU
    Shift Lever Switch Signal4
    [Shift SW Sig4]
    Shift lever switch signal (N):
    Open (OFF) or Gnd (ON)
    Gnd: Shift lever position in (N)
    Open: Other than above
    LSW4 (LSWN) terminal signal of transmission control ECU
    Shift Lever Switch Signal5
    [Shift SW Sig5]
    Shift lever switch signal (-):
    Open (OFF) or Gnd (ON)
    Gnd: Shift lever position in (-)
    Open: Other than above
    LSW5 (LSW-) terminal signal of transmission control ECU
    Shift Lever Check Signal1
    [Shift Chek Sig1]
    Check signal of shift lever switch signal 2:
    Open (ON) or Gnd (OFF)
    Open: Shift lever position in (R)
    Gnd: Other than above
    LS2C (LSRC) terminal signal of transmission ECU
    Reversal signal of LSW2 (LSWR)
    (ON and OFF reversed)
    Shift Lever Check Signal2
    [Shift Chek Sig2]
    Check signal of shift lever switch signal 3:
    Open (ON) or Gnd (OFF)
    Open: Shift lever position in (E), (M), (+) or (-)
    Gnd: Shift lever position in (R) or (N)
    LS3C (LSSC) terminal signal of transmission control ECU
    Reversal signal of LSW3 (LSWS)
    (ON and OFF reversed)
    Shift Lever Check Signal3
    [Shift Chek Sig3]
    Check signal of shift lever switch signal 4:
    Open (ON) or Gnd (OFF)
    Open: Shift lever position in (N)
    Gnd: Other than above
    LS4C (LSNC) terminal signal of transmission ECU
    Reversal signal of LSW4 (LSWN)
    (ON and OFF reversed)

    OK:
    When the shift lever is operated, the normal condition listed above is shown on the tester.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. INSPECT SHIFT LEVER POSITION SENSOR
C112726E01
  1. Disconnect the shift lever position sensor connector.

  1. Check the resistance when the sensor handles move to the applicable position.

    Standard Resistance:
    Shift Lever Position
    Shift Lever Terminals
    Specified Conditions
    R position
    4 - 9, 4 - 10, 4 - 11, 4 - 13
    9 - 10, 9 - 11, 9 - 13
    10 - 11, 10 - 13
    11 - 13
    Below 1 Ω
    N position
    2 - 4, 2 - 6, 2 - 10, 2 - 11
    4 - 6, 4 - 10, 4 - 11
    6 - 10, 6 - 11
    10 - 11
    Below 1 Ω
    E position
    2 - 3, 2 - 4, 2 - 11, 2 - 13
    3 - 4, 3 - 11, 3 - 13
    4 - 11, 4 - 13
    11 - 13
    Below 1 Ω
    M position
    2 - 3, 2 - 4, 2 - 11, 2 - 13
    3 - 4, 3 - 11, 3 - 13
    4 - 11, 4 - 13
    11 - 13
    Below 1 Ω
    + position
    2 - 3, 2 - 4, 2 - 11, 2 - 13
    3 - 4, 3 - 11, 3 - 13
    4 - 5, 4 - 11, 4 - 13
    5 - 11
    11 - 13
    Below 1 Ω
    - position
    2 - 3, 2 - 4, 2 - 11, 2 - 13
    3 - 4, 3 - 11, 3 - 13
    4 - 11, 4 - 12, 4 - 13
    11 - 12, 11 - 13
    Below 1 Ω

  1. Reconnect the shift lever position sensor connector.C112276E01



NG
REPLACE SHIFT LEVER POSITION SENSOR
OK


3. CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - TRANSMISSION CONTROL ECU)
C113922E02
  1. Disconnect the shift lever position sensor connector.

  1. Disconnect the transmission control ECU connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    LSW1 (D79-19) - LSW+ (D82-5)
    Below 1 Ω
    LSW2 (D79-18) - LSWR (D82-9)
    Below 1 Ω
    LSW3 (D79-17) - LSWS (D82-3)
    Below 1 Ω
    LSW4 (D79-16) - LSWN (D82-6)
    Below 1 Ω
    LSW5 (D79-15) - LSW- (D82-12)
    Below 1 Ω
    LS2C (D79-13) - LSRC (D82-2)
    Below 1 Ω
    LS3C (D79-12) - LSSC (D82-10)
    Below 1 Ω
    LS4C (D79-11) - LSNC (D82-13)
    Below 1 Ω
    LSW1 (D79-19) - Body ground
    10 kΩ or higher
    LSW2 (D79-18) - Body ground
    10 kΩ or higher
    LSW3 (D79-17) - Body ground
    10 kΩ or higher
    LSW4 (D79-16) - Body ground
    10 kΩ or higher
    LSW5 (D79-15) - Body ground
    10 kΩ or higher
    LS2C (D79-13) - Body ground
    10 kΩ or higher
    LS3C (D79-12) - Body ground
    10 kΩ or higher
    LS4C (D79-11) - Body ground
    10 kΩ or higher

  1. Reconnect the shift lever position sensor connector.

  1. Reconnect the transmission control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - BODY GROUND)
C112725E02
  1. Disconnect the shift lever position sensor connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    COM1 (D82-4) - Body ground
    Below 1 Ω
    COM2 (D82-11) - Body ground
    Below 1 Ω

  1. Reconnect the shift lever position sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY


← P0812 Reverse Input Circuit (from Nov 2005)P0821 Gear Lever "X" Position Circuit (from Nov 2005) →