2005-2008 Yaris · Service Manual TRANSMISSION

P0812 Reverse Input Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

As one judgment method, the transmission control ECU uses the back up light switch signal indicating whether the gear is in reverse or not. Receiving the signals from the back up light switch assembly and the shift and select stroke sensors, the transmission control ECU detects that the transmission gear is in reverse. If the signal from the back up light switch assembly does not match with the signal from the shift and select stroke sensors, the transmission control ECU sets the DTC.
DTC No.
DTC Detection Conditions
Trouble Areas
P0812
The transmission control ECU detects the following conditions simultaneously:
(1 trip detection logic)
  1. Shift and select stroke sensors send R position signal (information signal) to the transmission control ECU
  2. Back up light switch is OFF for 0.5 seconds
  1. Shift stroke sensor
  2. Select stroke sensor
  3. Back up light switch assembly
  4. Open or short in back up light switch circuit
  5. Transmission control ECU
P0812
The transmission control ECU detects the following conditions simultaneously:
(1 trip detection logic)
  1. Shift and select stroke sensors do not send R position signal (information signal) to the transmission control ECU
  2. Back up light switch is ON for 0.5 seconds
  1. Shift stroke sensor
  2. Select stroke sensor
  3. Back up light switch assembly
  4. Open or short in back up light switch circuit
  5. Transmission control ECU

WIRING DIAGRAM

C110755E03

INSPECTION PROCEDURE

NOTICE:
In shift and select stroke sensors replacement, perform [Initialization and Learning] and [Synchronization Position Calibration] after installing the sensors (Click here).
If the sensors are installed without performing [Initialization and Learning] and [Synchronization Position Calibration], it may cause driving performance degradation or system component breakage.


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and the tester ON.

  1. Select the following menu items: Powertrain / Multi-Mode M/T / Data List / T/M Reverse Switch Signal and Gear Position (Current).

    Items
    [Abbreviation]
    Measurement Items: Display
    Normal Conditions
    Diagnostic Notes
    T/M Reverse Switch Signal
    [T/M R SW Sig]
    Transmission reverse switch signal:
    Open or Gnd
    Gnd: Transmission gear in reverse
    Open: Other than above
    During malfunctions, indicator shows either ON or OFF continuously, regardless of gear position
    Gear Position (Current)
    [Gear Pos-Cur]
    Current gear position:
    Min.: 0, Max.: 7
    Actual gear position displayed
    0 = Neutral
    1 to 6 = 1st to 6th
    7 = Reverse

    OK:
    When the shift lever is operated, the normal condition listed above is shown on the tester.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. INSPECT BACK UP LIGHT SWITCH ASSEMBLY
C121799E01
  1. Remove the back up light switch assembly.

  1. Check the resistance when the switch condition is released and pushed.

    Standard resistance:
    Tester Connections
    Switch Conditions
    Specified Conditions
    1-2
    Released
    10 kΩ or higher
    1-2
    Pushed
    Below 1 Ω

  1. Reinstall the back up light switch assembly.



NG
REPLACE BACK UP LIGHT SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (BACK UP LIGHT SWITCH - TRANSMISSION CONTROL ECU)
C121798E01
  1. Disconnect the back up light switch assembly connector.

  1. Disconnect the transmission control ECU connector.

  1. Remove the back up light bulbs.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    RSW (A38-9) - (A51-1)
    Below 1 Ω
    RSW (A38-9) - Body ground
    10 kΩ or higher

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the back up light switch assembly and the body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    (A51-2) - Body ground
    10 to 14 V

  1. Reconnect the back up light switch assembly connector.

  1. Reconnect the transmission control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT SHIFT STROKE SENSOR
C112722E03
  1. Remove the shift stroke sensor.

  1. Measure the voltage between the terminals of the shift stroke sensor connector (main).

    1. Prepare 3 dry cell batteries (1.5 V) and 2 leads for connecting the batteries and the sensor.

    2. Connect the batteries in series.

    3. Connect the positive battery terminal to sensor terminal 3, and the negative battery terminal to sensor terminal 2.

    4. Check the voltage between terminals 1 and 2.

      Standard voltage (combined dry cell battery voltage of 4.5 V):
      Sensor Angle
      Terminal (1-2) Output Voltage
      55°
      Approximately 4.05 V
      0°
      Approximately 2.25 V
      -55°
      Approximately 0.45 V

      Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
      Sensor Angle
      Terminal (1-2) Output Voltage
      55°
      Approximately 4.5 V
      0°
      Approximately 2.5 V
      -55°
      Approximately 0.5 V

  1. C112722E04
    Measure the voltage between the terminals of the shift stroke sensor connector (sub).
    1. Connect the positive battery terminal to sensor terminal 6, and the negative battery terminal to sensor terminal 5.

    2. Check the voltage between terminals 4 and 5.

      Standard voltage (combined dry cell battery voltage of 4.5 V):
      Sensor Angle
      Terminal (4-5) Output Voltage
      55°
      Approximately 4.05 V
      0°
      Approximately 2.25 V
      -55°
      Approximately 0.45 V

      Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
      Sensor Angle
      Terminal (4-5) Output Voltage
      55°
      Approximately 4.5 V
      0°
      Approximately 2.5 V
      -55°
      Approximately 0.5 V

      NOTICE:
      1. Do not apply more than 6 V
      2. Do not use a sensor which has been dropped.

  1. Reinstall the shift stroke sensor (Click here).

  1. Perform [Initialization and Learning] (Click here) and [Synchronization Position Calibration] (Click here).



NG
REPLACE SHIFT STROKE SENSOR
OK


5. CHECK HARNESS AND CONNECTOR (SHIFT STROKE SENSOR - TRANSMISSION CONTROL ECU)
C113919E14
  1. Disconnect the shift stroke sensor connector.

  1. Disconnect the transmission control ECU connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    VCS2 (A38-30) - (C59-6)
    Below 1 Ω
    VSS2 (A38-29) - (C59-4)
    Below 1 Ω
    E2S2 (A38-28) - (C59-5)
    Below 1 Ω
    VCS1 (A38-19) - (C59-3)
    Below 1 Ω
    VSS1 (A38-18) - (C59-1)
    Below 1 Ω
    E2S1 (A38-17) - (C59-2)
    Below 1 Ω
    VCS2 (A38-30) - Body ground
    10 kΩ or higher
    VSS2 (A38-29) - Body ground
    10 kΩ or higher
    E2S2 (A38-28) - Body ground
    10 kΩ or higher
    VCS1 (A38-19) - Body ground
    10 kΩ or higher
    VSS1 (A38-18) - Body ground
    10 kΩ or higher
    E2S1 (A38-17) - Body ground
    10 kΩ or higher

  1. Reconnect the shift stroke sensor connector.

  1. Reconnect the transmission control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT SELECT STROKE SENSOR
C112722E03
  1. Remove the select stroke sensor.

  1. Measure the voltage between the terminals of the select stroke sensor connector (main).

    1. Prepare 3 dry cell batteries (1.5 V) and 2 leads for connecting the batteries and the sensor.

    2. Connect the batteries in series.

    3. Connect the positive battery terminal to sensor terminal 3, and the negative battery terminal to sensor terminal 2.

    4. Check the voltage between terminals 1 and 2.

      Standard voltage (combined dry cell battery voltage of 4.5 V):
      Sensor Angle
      Terminal (1-2) Output Voltage
      55°
      Approximately 4.05 V
      0°
      Approximately 2.25 V
      -55°
      Approximately 0.45 V

      Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
      Sensor Angle
      Terminal (1-2) Output Voltage
      55°
      Approximately 4.5 V
      0°
      Approximately 2.5 V
      -55°
      Approximately 0.5 V

  1. C112722E04
    Measure the voltage between the terminals of the select stroke sensor connector (sub).
    1. Connect the positive battery terminal to sensor terminal 6, and the negative battery terminal to sensor terminal 5.

    2. Check the voltage between terminals 4 and 5.

      Standard voltage (combined dry cell battery voltage of 4.5 V):
      Sensor Angle
      Terminal (4-5) Output Voltage
      55°
      Approximately 4.05 V
      0°
      Approximately 2.25 V
      -55°
      Approximately 0.45 V

      Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
      Sensor Angle
      Terminal (4-5) Output Voltage
      55°
      Approximately 4.5 V
      0°
      Approximately 2.5 V
      -55°
      Approximately 0.5 V

      NOTICE:
      1. Do not apply more than 6 V
      2. Do not use a sensor which has been dropped.

  1. Reinstall the select stroke sensor (Click here).

  1. Perform [Initialization and Learning] (Click here) and [Synchronization Position Calibration] (Click here).



NG
REPLACE SELECT STROKE SENSOR
OK


7. CHECK HARNESS AND CONNECTOR (SELECT STROKE SENSOR - TRANSMISSION CONTROL ECU)
C113919E15
  1. Disconnect the select stroke sensor connector.

  1. Disconnect the transmission control ECU connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    VCL2 (A38-31) - (C60-6)
    Below 1 Ω
    VSL2 (A38-32) - (C60-4)
    Below 1 Ω
    E2L2 (A38-24) - (C60-5)
    Below 1 Ω
    VCL1 (A38-20) - (C60-3)
    Below 1 Ω
    VSL1 (A38-21) - (C60-1)
    Below 1 Ω
    E2L1 (A38-22) - (C60-2)
    Below 1 Ω
    VCL2 (A38-31) - Body ground
    10 kΩ or higher
    VSL2 (A38-32) - Body ground
    10 kΩ or higher
    E2L2 (A38-24) - Body ground
    10 kΩ or higher
    VCL1 (A38-20) - Body ground
    10 kΩ or higher
    VSL1 (A38-21) - Body ground
    10 kΩ or higher
    E2L1 (A38-22) - Body ground
    10 kΩ or higher

  1. Reconnect the select stroke sensor connector.

  1. Reconnect the transmission control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY


← P0810 Clutch Position Control Error (from Nov 2005)P0820 Gear Lever "X-Y" Position Sensor Circuit (from Nov 2005) →