2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Jan 2006

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. INSTALL ROOF SIDE RAIL BRACKET RH

  1. C129259
    Insert the 2 hooks into the body holes and install the roof side rail bracket and tighten 2 the bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


2. INSTALL CURTAIN SHIELD AIRBAG BRACKET RH

  1. C128119
    Insert the 2 hooks into the body holes and install the curtain shield back bracket and tighten 1 the bolt.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


3. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

  1. Insert the 3 hooks into the body holes and install the curtain shield back bracket and tighten 9 the bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


    B135707E01

  1. C139109E01
    Connect the airbag connector.

    NOTICE:
    Lock the locking button securely.


4. INSTALL ROOF HEADLINING ASSEMBLY

  1. B134795
    Install the roof headlining into the front door.

  1. B134793
    w/ Curtain Shield Airbag:

    1. Engage the 4 hooks.

    2. Install the 2 clips.

  1. B134794
    w/o Curtain Shield Airbag:

    1. Engage the 2 claws and 4 hooks.

    2. Install the 2 clips.

  1. B134788
    Connect the antenna connector.

  1. Install the clamp.

  1. B134791
    for LHD:

    1. Connect the roof wire connector.

  1. B134792
    for RHD:

    1. Install the roof wire into the clamp.

    2. Connect the roof wire connector.

  1. B134790
    Install the 2 clamps.


5. INSTALL MAP LIGHT ASSEMBLY

  1. B138432
    Connect the map light connector.

  1. B114346
    Engage the 4 claws and install the map light.


6. INSTALL ROOM LIGHT ASSEMBLY

  1. B138432
    Connect the map light connector.

  1. B114346
    Engage the 4 claws and install the map light.


7. INSTALL VISOR HOLDER RH

  1. B114350E01
    Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.


8. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.


9. INSTALL VISOR ASSEMBLY RH

  1. B114304
    Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.

  1. B114351
    Engage the 4 claws and install the visor bracket cover.


10. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


11. INSTALL ASSIST GRIP SUB-ASSEMBLY

B134786

HINT:
The number of the assist grips varies with the specifications.

  1. B114302
    Engage the 2 springs and install the assist grip.


12. INSTALL ASSIST GRIP COVER

B134785

HINT:
The number of the assist grip covers varies with the specifications.

  1. B114352
    Engage the 2 claws and install the assist grip cover.


13. INSTALL INSTRUMENT PANEL BOX (for LHD)

B132335E01
  1. Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.

  1. B132337E01
    Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.


14. INSTALL INSTRUMENT UPPER PANEL SUB-ASSEMBLY

B130309E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the front side of the instrument panel.

  1. Engage the 7 clips at the rear side of the instrument panel.

    B132324

  1. Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.

    B132323E01

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. B132386
    Connect the passenger airbag connector and clamp.


15. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B132321E01
  1. Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B132319E01
    Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.

  1. Install the glove compartment door stopper onto the glove compartment door.


16. INSTALL COMBINATION METER ASSEMBLY

E116835E01
  1. Install the combination meter assembly with the 2 screws.

    NOTICE:
    Install the combination meter so that the rib of the combination meter is held between the instrument panel and the instrument cluster finish panel.

  1. Connect the 2 connectors.


17. INSTALL INSTRUMENT CLUSTER FINISH PANEL

E116833
  1. Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. E116834
    Engage the 5 claws and 5 clips and install the instrument cluster finish panel.


18. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

B132318
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.


19. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.


20. INSTALL REAR CONSOLE BOX ASSEMBLY

  1. B132349
    Engage the 4 claws and install the rear console box.

  1. Install the 2 bolts and 2 screws.

  1. Connect the clamp.


21. INSTALL CONSOLE BOX CARPET

  1. B132346
    Install the console box carpet.


22. INSTALL REAR CONSOLE BOX UPPER REAR PANEL SUB-ASSEMBLY

  1. B132348
    Connect the connector.

  1. Engage the 3 clips and 3 claws and install the console upper rear panel.


23. INSTALL REAR CONSOLE BOX UPPER FRONT PANEL SUB-ASSEMBLY

  1. B132347
    Engage the 5 clips and the claw and install the upper console panel.


24. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B132388
    Install the shift lever knob.


25. INSTALL INSTRUMENT LOWER CENTER PANEL FINISH PANEL

B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.


26. INSTALL FRONT PILLAR GARNISH RH

  1. B138439E01
    Remove the piece of cloth or nylon.

  1. B134787
    Install the 3 clamps.

  1. Connect the antenna connector.

  1. B134781E01
    Install a new special clip and the clip onto a new front pillar garnish.

  1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


27. INSTALL FRONT PILLAR GARNISH LH

  1. B138440
    Remove the piece of cloth or nylon.

  1. B134789
    Install the 4 clamps.

  1. B134782E01
    Install a new special clip and the clip onto the front pillar garnish.

  1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


28. INSTALL CENTER PILLAR UPPER GARNISH RH

  1. B134768
    Engage the 2 hooks and 2 clips and install the center pillar upper garnish.


29. INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.


30. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

  1. B114296
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


31. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


32. INSTALL SEAT BELT ANCHOR COVER CAP

B138431E02

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the seat belt anchor cover cap.


33. INSTALL CENTER PILLAR LOWER GARNISH RH

  1. B134767
    Engage the 2 clips and 3 claws and install the center pillar lower garnish.


34. INSTALL CENTER PILLAR LOWER GARNISH LH

HINT:
Use the same procedure as for the RH side.


35. INSTALL ROOF SIDE INNER GARNISH RH

  1. B134775E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B134774
    w/o Curtain Shield Airbag:

    1. Engage the 4 clips and the claw and install the roof side inner garnish.


36. INSTALL ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.


37. INSTALL REAR SEAT SIDE COVER RH

  1. B134776
    Engage the 2 clips and the 4 claws and install the rear seat side cover.


38. INSTALL REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.


39. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B134773E01
    Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.

    Paint mark:
    Area
    Color
    RH side
    Green
    LH side
    Red


40. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


41. INSTALL REAR DOOR SCUFF PLATE RH

  1. B134771
    Engage the 7 claws and install the rear door scuff plate.


42. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B134766E01
    Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.

    Paint mark:
    Area
    Color
    RH side
    Blue
    LH side
    Pink


44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


45. INSTALL COWL SIDE TRIM BOARD RH

  1. B114285
    Engage the stud bolt and the claw and install the cowl side trim board.


46. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


47. INSTALL FRONT DOOR SCUFF PLATE RH

  1. B134764
    Engage the 11 claws and install the front door scuff plate.


48. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


49. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)

B136275
  1. Install the luggage compartment trim inner pad.


50. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)

B136270
  1. Install the spare wheel cover.


51. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)

B136269
  1. Install the luggage compartment floor mat.


52. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B134981
    Engage the 3 hooks and install the rear seatback.

  1. Tighten the 3 bolts.

    Torque:
    7.9 N*m{ 80 kgf*cm , 70 in.*lbf }

  1. B138450E01
    Install the rear seat outer belt into the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.


53. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)

  1. B134926E01
    Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B134925
    Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.

  1. B134924
    Install the rear seat outer belt into the rear seat shoulder belt guide.


54. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)

  1. B134945E01
    Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B134944
    Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.

  1. B134943
    Install the rear seat outer belt into the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Seat Belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.


55. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly (Click here).

  1. for Fixed Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly (Click here).


56. INSTALL FRONT SEAT ASSEMBLY LH

B138318E01

NOTICE:
Follow the procedure described below in order to prevent the seat tracks from locking separately.

  1. Insert the 2 locating pins through the 2 body holes, place the front seat in the most forward position, and then make sure that the inner and outer seat tracks are locked securely.

  1. Using "Torx" socket wrench E10, tighten bolt 1 and then bolt 2 on the rear side.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Move the front seat to the most rearward position, and then make sure that the inner and outer seat tracks are locked securely.

  1. Using "Torx" socket wrench E10, tighten bolt 3 and then bolt 4 on the front side.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

    HINT:
    If the inner and outer seat tracks do not lock simultaneously, loosen the bolts and adjust the seat tracks.

  1. B138316
    w/ Front Seat Side Airbag:

    1. Connect the airbag connector.

  1. Connect the buckle switch connector.


57. INSTALL FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


58. INSTALL FRONT SEAT HEADREST ASSEMBLY

B138501E01

HINT:
Use the same procedure for both sides.

  1. Push in the lock button of the front seat headrest support and install the front seat headrest.


59. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


60. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Jan 2006)DISPOSAL (from Jan 2006) →