2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Jan 2006

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.

HINT:
The procedure described below is for the RH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.


1. INSTALL REAR AIRBAG SENSOR
  1. Confirm that the ignition switch is turned to off.

  1. Confirm that the negative battery terminal is detached.

    CAUTION:
    Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.

  1. B106578E01
    Insert the hook into the body hole and install the airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 90 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. Do not use a rear airbag sensor that has been dropped.
    2. Do not subject the rear airbag sensor to any impact or force.

  1. Confirm that there is no looseness by shaking the rear airbag sensor.

  1. B106579E01
    Connect the airbag connector.


2. INSTALL REAR SEAT SIDE COVER RH

  1. B134776
    Engage the 2 clips and the 4 claws and install the rear seat side cover.


3. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B134773E01
    Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.

    Paint mark:
    Area
    Color
    RH side
    Green
    LH side
    Red


4. INSTALL REAR DOOR SCUFF PLATE RH

  1. B134771
    Engage the 7 claws and install the rear door scuff plate.


5. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seatback Type)

B136275
  1. Install the luggage compartment trim inner pad.


6. INSTALL SPARE WHEEL COVER ASSEMBLY

B136270
  1. Install the spare wheel cover.


7. INSTALL LUGGAGE COMPARTMENT FLOOR MAT

B136269
  1. Install the luggage compartment floor mat.


8. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

  1. B134981
    Engage the 3 hooks and install the rear seatback.

  1. Tighten the 3 bolts.

    Torque:
    7.9 N*m{ 80 kgf*cm , 70 in.*lbf }

  1. B138450E01
    Install the rear seat outer belt into the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.


9. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)

  1. B134926E01
    Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B134925
    Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.

  1. B134924
    Install the rear seat outer belt into the rear seat shoulder belt guide.


10. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)

  1. B134945E01
    Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B134944
    Install the rear seatback cover with the 2 clips.

  1. Pull up the rear seatback.

  1. B134943
    Install the rear seat outer belt into the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Seat Belt:

    1. Install the rear center seat outer belt into the rear center seat shoulder belt guide.


11. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly (Click here).

  1. for Fixed Seat Type:

    1. Install the rear seat cushion cover pad sub-assembly (Click here).


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


13. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Jan 2006)COMPONENTS (from Aug 2005) →