2005-2008 Yaris · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005

CAUTION:
Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands.


1. INSTALL REAR SEAT TRACK ASSEMBLY LH

  1. B114679
    Install the rear seat track with the 2 nuts.

    Torque:
    33 N*m{ 335 kgf*cm , 24 ft.*lbf }


2. INSTALL REAR SEAT TRACK ASSEMBLY RH

  1. B114678
    Install the rear seat track with the 2 nuts.

    Torque:
    33 N*m{ 335 kgf*cm , 24 ft.*lbf }


3. INSTALL REAR SEAT SLIDE CONTROL CABLE

  1. B114677
    Install the 3 clips.

  1. B127712E01
    Install the rear seat slide control cable as shown in the illustration.


4. INSTALL REAR SEAT RECLINING CONTROL CABLE

  1. B127711E01
    Install the rear seat reclining control cable as shown in the illustration.


5. INSTALL RECLINING ADJUSTER INSIDE COVER

  1. B114674
    Engage the claw and install the reclining adjuster inside cover.

  1. Tighten the screw.


6. INSTALL REAR SEAT RECLINING INSIDE COVER LH

  1. B114672
    Engage the 2 claws and install the rear seat reclining inside cover.


7. INSTALL REAR SEAT RECLINING INSIDE COVER RH

  1. B114673
    Engage the 2 claws and install the rear seat reclining inside cover.


8. INSTALL REAR SEAT RECLINING OUTSIDE COVER RH

  1. B108404
    Install the rear seat reclining outside cover with the screw.


9. INSTALL REAR SEAT RECLINING OUTSIDE COVER LH

  1. B108405
    Install the rear seat reclining outside cover with the screw.


10. INSTALL REAR SEAT UNDER TRAY COVER

  1. B114671
    Install the rear seat under tray cover with the 4 clips.


11. INSTALL REAR SEATBACK COVER PAD SUB-ASSEMBLY

  1. B114670
    Install the rear seatback cover pad.

  1. B119892
    Fasten the 2 zippers.

  1. B114680E01
    Using hog ring pliers, install 5 new hog rings.

  1. B119890
    Install the rear seatback band.

  1. B126927
    w/ Tether Anchor Cover:

    1. Install the tether anchor cover with the screw.

    2. B126926
      Engage the 2 claws and close the cover.


12. INSTALL REAR SEAT HEADREST SUPPORT

B114681E03

HINT:
Use the same procedure for both sides.

  1. Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.

  1. Engage the 2 claws and install the rear seat headrest support.


13. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B126920
    Connect the rear seat reclining control cable and the rear seat slide control cable, and then install the rear seat lock control lever.

  1. Tighten the 2 screws.


14. INSTALL REAR SEAT LOCK STRIKER COVER

  1. B114682
    Engage the 2 claws and install the rear seat lock striker cover.


15. INSTALL REAR SEAT HEADREST ASSEMBLY

  1. B108395E01
    Push in the lock button of the rear seat headrest support and install the rear seat headrest.


16. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY

  1. B114683E01
    Engage the 7 hooks and install the rear seat cushion cover pad.

  1. Using hog ring pliers, install 4 new hog rings.


17. INSTALL REAR SEAT CUSHION ASSEMBLY

  1. B119887
    Install the bolts into the spacers.

  1. Using "Torx" socket wrench T45, install the rear seat cushion with the 2 bolts.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }


18. INSTALL REAR SEAT SIDE HINGE COVER

B119886

HINT:
Use the same procedure as for the opposite side.

  1. Engage the 4 claws and install the rear seat side hinge cover.


19. INSTALL REAR SEAT INNER BELT ASSEMBLY

  1. B114644E01
    Install the rear seat inner belt with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex areas of the rear seat back frame.

← DISASSEMBLY (from Aug 2005)INSTALLATION (from Aug 2005) →