REASSEMBLY
Removal / installation · Vehicles built from Nov 2005
- CAUTION:
- Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands.
| 1. INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY |
Engage the 2 claws and install the No. 2 seat adjuster control cable.

Connect the 2 cables.
Install the 5 clips.
| 2. INSTALL REAR SEAT RECLINING COVER |
Engage the 2 claws and install the rear seat reclining cover.

| 3. INSTALL REAR SEATBACK COVER PAD SUB-ASSEMBLY |
Engage the 2 hooks and install the rear seatback cover pad.

| 4. INSTALL REAR SEAT HEADREST SUPPORT |
![]() ![]() |
- HINT:
- Use the same procedure to install all the rear seat headrest supports.
Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.
Engage the 2 claws and install the rear seat headrest support.
| 5. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY |
Install the rear seatback board.

Engage the 3 hooks.

| 6. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY RH |
Install the rear center seat inner belt with the nut.

- Torque:
- 42 N*m{ 430 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not place the anchor plate over the convex areas of the rear seat frame adjuster.
| 7. INSTALL REAR SEAT RECLINING INNER COVER |
Engage the claw and install the rear seat reclining inner cover.

Using "Torx" socket wrench T25, tighten the screw.
| 8. INSTALL REAR SEAT RECLINING OUTER COVER |
Engage the 2 claws and install the rear seat reclining outer cover.

| 9. INSTALL REAR SEAT CUSHION UNDER COVER |
Engage the 6 claws and install the rear seat cushion under cover.

Engage the 4 clips and install the rear seatback cover.

| 10. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY |
Install the rear seat lock control lever with the screw.

Install the cover.

| 11. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
Push in the lock button of the rear seat headrest support and install the rear center seat headrest.

| 12. INSTALL REAR SEAT HEADREST ASSEMBLY |
Push in the lock button of the rear seat headrest support and install the rear seat headrest.

| 13. INSTALL REAR SEAT LEG SUB-ASSEMBLY |
Engage the 4 claws and install the 4 rear seat cushion hinge retainers.

Using "Torx" socket wrench T40, install the rear seat leg with the 2 bolts.

- Torque:
- 21 N*m{ 215 kgf*cm , 16 ft.*lbf }
| 14. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY |
Engage the 9 hooks and install the rear seat cushion cover pad.

| 15. INSTALL REAR SEAT CUSHION SIDE OUTER COVER |
Engage the claw and install the rear seat cushion side outer cover.

Engage the 2 claws and install the 2 retainers.

| 16. INSTALL REAR SEAT CUSHION SIDE INNER COVER |
Engage the claw and install the rear seat cushion side inner cover.

Engage the 2 claws and install the 2 retainers.

| 17. INSTALL REAR SEAT CUSHION ASSEMBLY |
Using "Torx" socket wrench T40, install the rear seat cushion with the 2 bolts.

- Torque:
- 21 N*m{ 215 kgf*cm , 16 ft.*lbf }
| 18. INSTALL REAR SEAT CUSHION INNER COVER |
Engage the 3 claws and install the rear seat cushion inner cover.

| 19. REMOVE REAR SEAT CUSHION OUTER COVER |
Engage the 3 claws and install the rear seat cushion outer cover.

| 20. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY LH |
Install the rear center seat inner belt with the bolt.

- Torque:
- 42 N*m{ 430 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not place the anchor plate over the convex areas of the rear seat frame adjuster.
Install the belt into the rear seat cushion band.
| 21. INSTALL REAR SEAT INNER BELT ASSEMBLY |
Install the rear seat inner belt with the bolt.

- Torque:
- 42 N*m{ 430 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Do not place the anchor plate over the convex areas of the rear seat frame adjuster.

