2005-2008 Yaris · Service Manual STEERING

C1511/11 Torque Sensor 1 Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The torque sensor converts the rotation torque input from the steering wheel into electric signals and sends them to the power steering ECU.
DTC No.
Detection Item
Trouble Area
C1511/11
Torque sensor (TRQ1) signal error or stop
  1. Torque sensor (built into steering column assembly)
  1. Power steering ECU
C1512/12
Torque sensor (TRQ2) signal error or stop
C1513/13
Deviation between torque sensor TRQ1 and TRQ2 exceeds specified value
C1514/14
Torque sensor power source voltage error
C1517/17
Temporary control due to malfunction related to torque sensor continues for long time

WIRING DIAGRAM

F044868E02

INSPECTION PROCEDURE


1. READ VALUE OF DATA LIST (TORQUE SENSOR OUTPUT)
  1. Connect the intelligent tester to DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the items [Torque Sensor 1 Output] and [Torque Sensor 2 Output] in the DATA LIST.

  1. Measure the voltage.

    Item
    Item Description
    Inspection Condition
    Reference Value
    Torque Sensor 1 Output
    Torque sensor 1 output value
    Minimum: 0 V, Maximum: 5 V
    1. Steering wheel not turned (without load)
    2. Turning steering wheel to right with vehicle stopped
    3. Turning steering wheel to left with vehicle stopped
    1. 2.3 to 2.7 V
    2. 2.5 to 4.7 V
    3. 0.3 to 2.5 V
    Torque Sensor 2 Output
    Torque sensor 2 output value
    Minimum: 0 V, Maximum: 5 V

  1. Check the difference in the values between [Torque Sensor 1 Output] and [Torque Sensor 2 Output].

OK:
The voltage difference is below 0.3 V.



OK
CHECK INTERMITTENT PROBLEMS
NG


2. INSPECT POWER STEERING ECU (OUTPUT)
F046432E01
  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified condition
    TRQV (c1-6) - TRQG (c1-8)
    Ignition switch on (IG)
    7.5 to 8.5 V



NG
REPLACE POWER STEERING ECU
OK


3. INSPECT STEERING COLUMN ASSEMBLY (TORQUE SENSOR)
F046432E02
  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition (Steering Position)
    Specified Condition
    TRQ1 (c1-5) - TRQG (c1-8)
    Center position
    2.3 to 2.7 V
    TRQ2 (c1-7) - TRQG (c1-8)
    Center position
    2.3 to 2.7 V
    TRQ1 (c1-5) - TRQG (c1-8)
    Turned to right
    2.5 to 4.7 V
    TRQ2 (c1-7) - TRQG (c1-8)
    Turned to right
    2.5 to 4.7 V
    TRQ1 (c1-5) - TRQG (c1-8)
    Turned to left
    0.3 to 2.5 V
    TRQ2 (c1-7) - TRQG (c1-8)
    Turned to left
    0.3 to 2.5 V



NG
REPLACE STEERING COLUMN ASSEMBLY
OK

REPLACE POWER STEERING ECU


← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2006)C1515/15 Torque Sensor Zero Point Adjustment is not Initialized (from Aug 2005) →