2005-2008 Yaris · Service Manual STEERING

DIAGNOSTIC TROUBLE CODE CHART

Diagnostic trouble codes · Vehicles built from Jan 2006

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006

HINT:
  1. If any DTCs are displayed during the DTC check, inspect the circuit listed for those DTCs. For details of each DTC, refer to the page indicated in the DTC chart.
  2. Test mode code C1571/71 is stored during the transition to test mode. This code does not indicate a malfunction since the code will be cleared when the ECU determines that the sensor is normal. The test mode code is cleared simultaneously when test mode is terminated.
  3. The P/S warning light remains illuminated during test mode and starts blinking when the speed sensor is determined to be normal.

 
DTC No.
Detection Item
Trouble Areas
Normal Return
P/S Warning Light
See page
C1511/11
Torque Sensor 1 Malfunction
  1. Steering column Assembly (Torque sensor)
  2. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1512/12
Torque Sensor Circuit Malfunction
  1. Steering column assembly (Torque sensor)
  2. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1513/13
Torque Sensor Circuit Malfunction
  1. Steering column assembly (Torque sensor)
  2. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1514/14
Torque Sensor Power Source Circuit Malfunction
  1. Steering column assembly (Torque sensor)
  2. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1515/15
Torque Sensor Zero Point Adjustment is not Initialized
  1. Torque sensor zero point calibration not performed
  2. Steering column assembly
After calibrating torque sensor zero point
○
Click here
C1516/16
Torque Sensor Zero Point Adjustment Incomplete
  1. Torque sensor zero point calibration failure
  2. Steering column assembly
After calibrating torque sensor zero point normally
○
Click here
C1517/17
Torque Sensor Hold Malfunction
  1. Steering column assembly (Torque sensor)
  2. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1524/24
Motor Circuit Malfunction
  1. Steering column assembly
  2. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1531/31
EPS ECU Circuit Malfunction
  1. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1532/32
EPS ECU Circuit Malfunction
  1. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1533/33
EPS ECU Circuit Malfunction
  1. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1534/34
EPS ECU Circuit Malfunction
  1. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1535/35 *1
Steering Wheel Location Data Error
  1. Power steering ECU
-
○
Click here
C1541/41 *2
Speed Sensor Malfunction
  1. Speed sensor
  2. Speed sensor circuit
  3. Combination meter
  4. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1542/42 *2
Speed Sensor Malfunction
  1. Speed sensor
  2. Speed sensor circuit
  3. Combination meter
  4. Power steering ECU
Return to normal
X
Click here
C1551/51
IG Power Source Circuit Malfunction
  1. ECU-IG fuse
  2. IG power source circuit
  3. Power steering ECU
Ignition switch on (IG) again or after normal confirmation
○
Click here
C1552/52
PIG Power Source Circuit
  1. EPS fuse
  2. PIG power source circuit
  3. Power steering ECU
Ignition switch on (IG) again or after normal confirmation
○
Click here
C1553/53 *1
When Resetting Voltage, Vehicle is Being Driven
  1. IG and PIG power source circuit
  2. Power steering ECU
Ignition switch on (IG) again or after normal confirmation
○
Click here
C1554/54
EPS Relay Circuit
  1. EPS fuse
  2. PIG power source circuit
  3. Power steering ECU
Ignition switch on (IG) again
○
Click here
C1555/55
EPS Motor Relay Circuit
  1. Power steering ECU
  2. Steering column assembly (Power steering motor)
Ignition switch on (IG) again
○
Click here
C1571/71 *2
Speed Sensor Malfunction (Test Mode DTC)
  1. Speed sensor
  2. Speed sensor circuit
  3. Combination meter
  4. Power steering ECU
-
-
Click here
U0073
Control Module Communication Bus OFF
  1. CAN communication system
Ignition switch on (IG) again or after normal confirmation
○
Click here
U0105
Lost Communication with ECM
  1. CAN communication system
  2. ECM
Ignition switch on (IG) again or after normal confirmation
○
Click here
U0121 *3
Lost Communication with Anti-lock Brake System (ABS) Control Module
  1. CAN communication system
  2. Skid control ECU
Ignition switch on (IG) again or after normal confirmation
○
Click here
(Warning light) ○---turn on, X---turn off (Normal reset)
*1--- for SEDAN, *2---w/o ABS, *3---w/ ABS
← DIAGNOSTIC TROUBLE CODE CHART (Aug 2005 – Dec 2005)C1511/11 Torque Sensor 1 Malfunction (+ C1512/12, C1513/13, C1514/14, C1517/17) (from Aug 2005) →