2005-2008 Yaris · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL REAR COIL SPRING LH
  1. Install the coil spring insulator lower onto the axle beam.

  1. C110329E01
    Install the coil spring insulator upper so that its gap fits onto the end of coil spring.

  1. C112606E01
    Install the coil spring onto the axle beam.

    NOTICE:
    The paint mark of the coil spring should be towards the underside and rear side of the vehicle.


2. INSTALL REAR COIL SPRING RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


3. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER LH

C106031
  1. Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.

  1. Jack up the axle beam slowly, and provisionally install the shock absorber (lower side) with the bolt and nut onto the axle beam.

  1. Install the suspension support and cushion retainer.

  1. C106033
    While holding the piston rod, install a new nut (lower nut) to the specified standard.

    Standard:
    15 to 18 mm (0.591 to 0.709 in.)

  1. C106030
    While holding the piston rod, tighten a new nut (upper nut).

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


4. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


5. INSTALL REAR SHOCK ABSORBER CAP LH

6. INSTALL REAR SHOCK ABSORBER CAP RH

7. INSTALL REAR ABSORBER CAP

8. INSTALL REAR LH FLEXIBLE HOSE

C107567E01
  1. Connect the flexible hose onto the axle beam with a new clip.

  1. Using SST, install the brake tube.

    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


9. INSTALL REAR RH FLEXIBLE HOSE

HINT:
The installation procedure for the RH side is the same as that for the LH side.


10. INSTALL SKID CONTROL SENSOR WIRE

C107566
  1. Install the skid control sensor wire onto the axle beam with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. C107565
    Connect the skid control sensor wire connector.


11. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


12. STABILIZE SUSPENSION
  1. Lower the vehicle from the jack.

  1. Bounce the vehicle up and down several times to stabilize the suspension.


13. FULLY TIGHTEN REAR AXLE BEAM

C107574E01
  1. Suspend the jack on the rear axle spring seat and adjust the length of the shock absorber to the reference value.

    Length of shock absorber:
    220 mm (8.7 in.)

  1. Fully tighten the 2 bolts.

    Torque:
    90 N*m{ 918 kgf*cm , 67 ft.*lbf }


14. FULLY TIGHTEN REAR SHOCK ABSORBER LH
  1. Fully tighten the shock absorber (lower side) with the bolt.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


15. FULLY TIGHTEN REAR SHOCK ABSORBER RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


17. FILL RESERVOIR WITH BRAKE FLUID

C137247E01
  1. Remove the cowl top ventilator louver.

  1. C130290E01
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4


18. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C130291E01
    w/o VSC:

    1. Using SST, disconnect the brake tubes from the master cylinder.

      SST
      09023-00100  

  1. w/ VSC:

    1. Using SST, disconnect the brake tubes from the master cylinder.

      SST
      09023-38200  

  1. C130292E01
    Slowly depress the brake pedal and hold it there (Step A).

  1. C130293E01
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C130291E01
    w/o VSC:

    1. Using SST, connect the brake tubes to the master cylinder.

      SST
      09023-00100  

      Torque:
      for use without SST:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }
      for use with SST:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.

  1. w/ VSC:

    1. Using SST, connect the brake tubes to the master cylinder.

      SST
      09023-38200  

      Torque:
      for use without SST:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }
      for use with SST:
      18 N*m{ 180 kgf*cm , 13 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.


19. BLEED BRAKE LINE

C130294
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    Front Disc Brake:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }
    Rear Drum Brake:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Rear Disc Brake:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


20. BLEED BRAKE ACTUATOR (w/ VSC)

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. A107926E08
    Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Select AIR BLEEDING on the intelligent tester.

    HINT:
    Refer to the intelligent tester operator's manual for further details.

  1. Bleed the air out of the brake line when Step 1: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. C130294
      Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    3. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    4. Repeat steps E and F until all air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2: Inhalation appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the intelligent tester (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the intelligent tester display (Step H).

    4. Repeat steps G and H until all air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there.

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, then release the brake pedal (Step J).

    5. Repeat steps I and J until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. C130294
      Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step K).

    3. When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step L).

    4. Repeat steps K and L until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      Front Disc Brake:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }
      Rear Drum Brake:
      9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
      Rear Disc Brake:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    7. Make sure that the air bleeding is complete by referring to the intelligent tester display.


21. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4


22. CHECK FOR BRAKE FLUID LEAKAGE

23. INSPECT REAR WHEEL ALIGNMENT
(Click here)

24. CHECK ABS SENSOR SIGNAL (w/o VSC)
(Click here)

25. CHECK VSC SENSOR SIGNAL (w/ VSC)
(Click here)
← REMOVAL (from Nov 2005)COMPONENTS (from Jan 2006) →