2005-2008 Yaris · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL CLUTCH PEDAL NO.1 CUSHION

C115318
  1. Install the clutch pedal No. 1 cushion onto the clutch pedal.


2. INSTALL CLUTCH PEDAL BUSH

C115309
  1. Apply MP grease to the 2 bushes and collar.

  1. Install the 2 bushes and collar onto the clutch pedal.


3. INSTALL CLUTCH PEDAL PAD

4. INSTALL CLUTCH PEDAL SUB-ASSEMBLY

C115308
  1. Install the clutch pedal onto the clutch pedal support with the bolt and the nut.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

    HINT:
    Install the bolt from the left side of the vehicle.


5. INSTALL CLUTCH PEDAL SPRING

6. INSTALL CLUTCH PEDAL STOPPER BOLT

C115317
  1. Install the clutch pedal stopper bolt so that its end touches the clutch pedal cushion.

    HINT:
    Tighten the lock nut to the specified torque when adjusting the clutch pedal.


7. INSTALL CLUTCH START SWITCH ASSEMBLY

C115315
  1. Install the clutch start switch with the nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


8. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

C115316
  1. Install the clutch pedal support onto the vehicle with the bolt.

    Torque:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }

  1. Connect the clutch start switch connector.

  1. Connect the wire harness clamp.


9. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

C136386
  1. Install the clutch master cylinder so that its flat section is at a right angle to the pedal.

  1. C115307
    Install the clutch master cylinder with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


10. CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

C115313
  1. Using SST, connect the flexible hose tube.

    SST
    09023-00101  

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }


11. INSTALL CLUTCH RESERVOIR TUBE
  1. Connect the clutch reservoir tube to the clutch master cylinder assembly with the clip.


12. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER
(Click here)

13. INSTALL BRAKE BOOSTER ASSEMBLY
(Click here)

14. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY
  1. Pull back the floor carpet.

  1. C127616E01
    Check that the pedal height is correct.

    Pedal height from floor:
    122.4 to 132.4 mm (4.819 to 5.213 in.) 1KR-FE/2SZ-FE
    133.0 to 143.0 mm (5.236 to 5.630 in.) 1ND-TV

  1. If the pedal height is not as specified, adjust it as follows.

    1. Loosen the lock nut and turn the stopper bolt until the correct height is obtained.

    2. Tighten the lock nut.

      Torque:
      16 N*m{ 160 kgf*cm , 12 ft.*lbf }


15. INSPECT CLUTCH START SWITCH ASSEMBLY

C115311
  1. Check that the engine does not start when the clutch pedal is released.

  1. Check that the engine starts when the clutch pedal is fully depressed.
    If necessary, replace the clutch start switch assembly.


16. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY NO.1

  1. B114572
    Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.

← REMOVAL (from Nov 2005)COMPONENTS (from Nov 2005) →