VC Output Circuit
Circuit diagnosis · Vehicles built from Nov 2006
DESCRIPTION
The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
- HINT:
- Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned on (IG). The MIL goes off when the engine is started.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK MIL CONDITION |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch on (IG).
- OK:
- MIL lights up.
|
|
||||
| OK | ||
| ||
| 2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Check for communication between the tester and ECM.
- Result:
Result
Proceed to
Communication possible
A
Communication not possible
B
|
|
||||
| B | |
| 3. CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle body connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the throttle body connector.
|
|
||||
| B | |
| 4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the accelerator pedal position sensor connector.
|
|
||||
| B | |
| 5. CHECK MIL (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT) |
Disconnect the camshaft position sensor (for intake camshaft) connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the camshaft position sensor (for intake camshaft) connector.
|
|
||||
| B | |
| 6. CHECK MIL (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT) |
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the camshaft position sensor (for exhaust camshaft) connector.
|
|
||||
| B | |
| 7. CHECK HARNESS AND CONNECTOR (VC CIRCUIT) |
Disconnect the throttle body connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the camshaft position sensor (for intake camshaft) connector.
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the ECM connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for short):
Tester Connection
Condition
Specified Condition
C20-67 (VCTA) - Body ground
Always
10 kΩ or higher
A21-57 (VCPA) - Body ground
Always
10 kΩ or higher
A21-58 (VCP2) - Body ground
Always
10 kΩ or higher
C20-70 (VCVI) - Body ground
Always
10 kΩ or higher
C20-117 (VC) - Body ground
Always
10 kΩ or higher
Reconnect the throttle body connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the camshaft position sensor (for intake camshaft) connector.
Reconnect the camshaft position sensor (for exhaust camshaft) connector.
Reconnect the ECM connectors.
|
|
||||
| OK | ||
| ||
