2005-2008 Yaris · Service Manual ENGINE

Fuel Pump Control Circuit

Circuit diagnosis · Vehicles built from Nov 2006

DESCRIPTION

When the engine is cranked, the ST (Starter) relay drive signal output from the STAR terminal of the ECM is input to the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates.
While the NE signal is input to the ECM with the engine running, the ECM turns the Tr1 on continuously.
A159169E01

WIRING DIAGRAM

A159170E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPD)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.

    Result:
    Result
    Proceed to
    Fuel pump operating sound does not occur
    A
    Fuel pump operating sound occurs
    B



B
Go to step 8
A


2. INSPECT MAIN BODY ECU (C/OPN RELAY INPUT VOLTAGE)
A116124E22
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    4B-11 - Body ground
    Ignition switch off
    Below 1 V
    4F-4 - Body ground
    4B-11 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    4F-4 - Body ground

Result:
Result
Proceed to
Outside standard range
A
Within standard range
B



B
Go to step 4
A


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY)
A112627E09
  1. Remove the integration relay from the engine room R/B and J/B.

  1. Disconnect the main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    1B-4 - 4F-4
    Always
    Below 1 Ω
    1A-4 - 4B-11
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    4F-4 - Body ground
    Always
    10 kΩ or higher
    4B-11 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT (Click here)

4. INSPECT MAIN BODY ECU (C/OPN RELAY)
A116124E23
  1. Remove the main body ECU.

  1. Connect the battery positive terminal to the 4D-1 terminal, and connect the battery negative terminal to the 4E-5 terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    4A-8 - 4B-11
    Always
    10 kΩ or higher
    Battery voltage applied to terminals 4D-1 and 4E-5
    Below 1 Ω

    HINT:
    The relay coil circuit between 4D-1 and 4E-5 is not through the IGN fuse.

  1. Reinstall the main body ECU.



NG
REPLACE MAIN BODY ECU
OK


5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
A115687E08
  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    4E-5 - A21-7 (FC)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A21-7 (FC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FUEL PUMP - BODY GROUND)
A116150E04
  1. Check the harness and the connectors between the main body ECU and the fuel pump.

    1. Disconnect the main body ECU connector.

    2. Disconnect the fuel pump connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      4A-8 - J5-4
      Always
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Condition
      Specified Condition
      4A-8 - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the fuel pump connector.

  1. Check the harness and connector between the fuel pump and the body ground.

    1. Disconnect the fuel pump connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      J5-5 - Body ground
      Always
      Below 1 Ω

    3. Reconnect the fuel pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FUEL PUMP
A159459E01
  1. Inspect fuel pump resistance.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      20°C (68°F)
      0.2 to 3.0 Ω

  1. Inspect fuel pump operation.

    1. Apply battery voltage to the fuel pump terminals.

    2. Check that the fuel pump operates.

      NOTICE:
      1. This test must be done quickly (within 10 seconds) to prevent the coil from burning out.
      2. Keep the fuel pump as far away from the battery as possible.
      3. Always switch at the battery side.



NG
REPLACE FUEL PUMP
OK

REPLACE ECM

8. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is on (IG) and the engine starts.

    Standard:
    Ignition Switch Conditions
    Tester Display (Starter Signal)
    On (IG)
    OFF
    Engine Start
    ON



NG
REPAIR OR REPLACE STARTING SYSTEM (Click here)
OK


9. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Read the value while cranking.

    OK:
    The value is the same as the actual engine speed and is displayed with no interruption on the tester.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR CIRCUIT (Click here)
OK

REPLACE ECM


← VC Output Circuit (from Nov 2006)Fuel Injector Circuit (from Nov 2006) →