2005-2008 Yaris · Service Manual ENGINE

Variable Resistor Circuit

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

The variable resistor is used to adjust the concentration of CO in the exhaust during idling. By turning the idle mixture adjusting screw, located on the variable resistor, clockwise, the contact inside the resistor is moved and the voltage at the VAF terminal rises accordingly. Conversely, turning the adjusting screw counterclockwise reduces the VAF terminal voltage. When the VAF terminal voltage rises, the ECM increases the fuel injection volume slightly, thus making the air-fuel ratio slightly richer.

WIRING DIAGRAM

A107929E01

INSPECTION PROCEDURE

HINT:
Always use a CO meter when adjusting the concentration of CO during idling. If a CO meter is not available, do not attempt to adjust the idling CO concentration.


1. CHECK CO/HC

  1. A107933E01
    Ensure the following:
    1. All the vacuum lines are properly connected.

    2. The CO meter is properly calibrated.

  1. Start the engine.

  1. Ensure the following:

    1. The parking brake is securely applied.

    2. The transmission gear is in neutral.

    3. All the accessories are switched off.

  1. Warm up the engine and check that the idling speed is appropriate.

  1. Race the engine at 2,500 rpm for about 2 minutes.

  1. Insert a tester probe at least 40 cm (1.3 ft) into the tailpipe.

  1. Measure the CO concentration 1 to 3 minutes after racing the engine to allow the concentration to stabilize.

Standard CO concentration rate at idling:
1.0 to 2.0 %

HINT:
If the result is outside the standard range shown above, maintain the measurement conditions obtained during this procedure. The measurement conditions are used in the CO concentration adjustment procedure described below.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. ADJUST IDLING CO CONCENTRATION

  1. A107930E01
    Ensure all the conditions prepared in the measurement procedure.

  1. Regulate the idling CO concentration so that it is within 1.0 to 2.0 %.

    HINT:
    Use SST and the idle mixture adjusting screw located on the C37 variable resistor. By turning the adjusting screw, the idling CO concentration rate can be regulated.

    Reference:
    Result
    Proceed To
    Unable to obtain standard concentration rate
    A
    Standard concentration rate obtained
    B



B
ADJUSTMENT COMPLETE
A


3. INSPECT VARIABLE RESISTOR

  1. A107931E01
    Remove the C37 variable resistor.

  1. Measure the resistance between terminals 1 and 2 of the variable resistor.

    Standard resistance:
    Tester Connections
    Specified Conditions
    E2 (1) - VC (2)
    3.5 to 6.5 kΩ

  1. Measure the resistance between terminals 1 and 3 when the idle mixture adjusting screw is turned fully clockwise and fully counterclockwise.

    Standard resistance:
    Tester Connections
    Adjusting Screw
    Specified Conditions
    E2 (1) - VAF (3)
    Turned fully clockwise
    3.5 to 6.5 kΩ
    Turned fully counterclockwise
    0 kΩ

HINT:
When the adjusting screw is turned fully clockwise, the resistance is the same as the measurement value between terminals 1 and 2. When the adjusting screw is turned fully counterclockwise, the resistance changes to 0 kΩ.

  1. Reinstall the variable resistor.



NG
REPLACE VARIABLE RESISTOR
OK


4. INSPECT ECM (VC VOLTAGE)

  1. A107928E01
    Disconnect the C37 variable resistor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the variable resistor connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    E2 (C37-1) - VC (C37-2)
    4.5 to 5.5 V

  1. Reconnect the variable resistor connector.



OK
REPLACE ECM
NG


5. CHECK HARNESS AND CONNECTOR (VARIABLE RESISTOR - ECM)

  1. A115656E01
    Disconnect the C37 variable resistor connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    E2 (C37-1) - EVAF (C20-87)
    Below 1 Ω
    VC (C37-2) - VC (C20-117)
    VAF (C37-3) - VAF (C20-64)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    E2 (C37-1) or EVAF (C20-87) - Body ground
    10 kΩ or higher
    VC (C37-2) or VC (C20-117) - Body ground
    VAF (C37-3) or VAF (C20-64) - Body ground

  1. Reconnect the variable resistor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← Cranking Holding Function Circuit (from Aug 2005)MIL Circuit (Aug 2005 – Dec 2005) →