TERMINALS OF ECM
System information · Vehicles built from Aug 2005


- HINT:
- The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the STD Voltage column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Symbols (Terminals No.) |
Wiring Colors |
Terminal Descriptions |
Conditions |
STD Voltages |
| BATT (A32-22) - E1 (A32-1) |
V - W-B |
Battery (for measuring battery voltage and for ECM memory) |
Always |
9 to 14 V |
| IGSW (A32-4) - E1 (A32-1) |
R - W-B |
Ignition switch |
Ignition switch on (IG) |
9 to 14 V |
| +B (A32-24) - E1 (A32-1) |
B - W-B |
Power source of ECM |
Ignition switch on (IG) |
9 to 14 V |
| +B1 (A32-23) - E1 (A32-1) |
B - W-B |
Power source of ECM |
Ignition switch on (IG) |
9 to 14 V |
| MREL (A32-6) - E1 (A32-1) |
GR - W-B |
EFI relay |
Ignition switch on (IG) |
9 to 14 V |
| VC (C33-54) - ETA (C33-39) |
W - SB |
Power source of throttle position sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| VCPA (A32-11) - EPA (A32-9) |
B - G |
Power source of accelerator pedal position sensor (for VPA) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| VCP2 (A32-19) - EPA2 (A32-17) |
W - BR |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| VC2 (C33-40) - E21 (C33-35) |
W - G |
Power source of manifold absolute pressure sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| VC2R (C33-74) - E1 (A32-1) |
LG - W-B |
Power source of camshaft position sensor (specific voltage) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| PIM (C33-20) - E21 (C33-35) |
GR - G |
Manifold absolute pressure sensor |
Idling |
1.2 to 2.0 V |
| VTA1 (C33-21) - ETA (C33-39) |
Y - SB |
Throttle position sensor (for engine control) |
Ignition switch on (IG), Accelerator pedal fully released |
0.2 to 1.0 V |
| VTA1 (C33-21) - ETA (C33-39) |
Y - SB |
Throttle position sensor 1 (for engine control) |
Ignition switch on (IG), Accelerator pedal fully depressed |
4.2 to 4.6 V |
| VTA2 (C33-37) - ETA (C33-39) |
GR - SB |
Throttle position sensor 2 (for engine control) |
Ignition switch on (IG), Accelerator pedal fully released |
4.2 to 4.8 V |
| VTA2 (C33-37) - ETA (C33-39) |
GR - SB |
Throttle position sensor 2 (for engine control) |
Ignition switch on (IG), Accelerator pedal fully depressed |
0.2 to 1.0 V |
| VPA (A32-10) - EPA (A32-9) |
R - G |
Accelerator pedal position sensor (for engine control) |
Ignition switch on (IG), Accelerator pedal fully released |
0.7 to 1.2 V |
| VPA (A32-10) - EPA (A32-9) |
R - G |
Accelerator pedal position sensor 1 (for engine control) |
Ignition switch on (IG), Accelerator pedal fully depressed |
2.8 to 4.6 V |
| VPA2 (A32-18) - EPA2 (A32-17) |
L - BR |
Accelerator pedal position sensor 2 (for engine control) |
Ignition switch on (IG), Accelerator pedal fully released |
1.2 to 2.0 V |
| VPA2 (A32-18) - EPA2 (A32-17) |
L - BR |
Accelerator pedal position sensor 2 (for engine control) |
Ignition switch on (IG), Accelerator pedal fully depressed |
3.6 to 4.0 V |
| THA (C33-76) - E21 (C33-35) |
P - G |
Intake air temperature sensor |
Idling, Intake air temperature 20°C (68°F) |
1.5 to 3.0 V |
| THW (C33-56) - E2 (C33-36) |
L - P |
Engine coolant temperature sensor |
Idling, Engine coolant temperature 80°C (176°F) |
0.2 to 1.0 V |
| #1 (C33-43) - E01 (A32-20) #2 (C33-42) - E01 (A32-20) #3 (C33-44) - E01 (A32-20) |
SB - W-B GR - W-B P - W-B |
Injector |
Ignition switch on (IG) |
9 to 14 V |
| IGT1 (C33-12) - E1 (A32-1) IGT2 (C33-10) - E1 (A32-1) IGT3 (C33-11) - E1 (A32-1) |
W - W-B O - W-B G - W-B |
Ignition coil with igniter (ignition signal) |
Idling |
Pulse generation (See waveform 1) |
| G1 (C33-13) - G- (C33-32) |
R - W-B |
Camshaft position sensor |
Idling |
Pulse generation (See waveform 2) |
| NE+ (C33-60) - NE- (C33-81) |
L - P |
Crankshaft position sensor |
Idling |
Pulse generation (See waveform 2) |
| STA (A32-27) - E1 (A32-1) |
BR - W-B |
Starter signal |
Cranking |
5.5 V or more |
| STSW (A32-12) - E1 (A32-1) |
B - W-B |
Engine cranking required signal |
Ignition switch on (IG) → Cranking |
Push start type engine switch: Below 1 V → 9 to 14 V momentary Mechanical type ignition switch: Below 1 V → 9 to 14 V |
| STAR (C33-80) - E1 (A32-1) |
O - W-B |
Starter relay drive signal |
Cranking |
9 to 14 V |
| ACCR (C33-4) - E1 (A32-1) |
G - W-B |
Accessory power cut signal |
Ignition switch on (IG) → Cranking |
9 to 14 V → Below 1 V |
| FC (C33-63) - E1 (A32-1) |
V - W-B |
Fuel pump control |
Ignition switch on (IG) |
9 to 14 V |
| OX1A (C33-18) - E11 (C33-17) |
W - O |
Heated oxygen sensor (Sensor 1) |
Engine speed maintained at 2,500 rpm for 2 minutes after warming up sensor |
Pulse generation (See waveform 3) |
| OX1B (C33-55) - E12 (C33-34) |
Y - BR |
Heated oxygen sensor (Sensor 2) |
Engine speed maintained at 2,500 rpm for 2 minutes after warming up sensor |
Pulse generation (See waveform 4) |
| HT1A (C33-41) - E1 (A32-1) |
G - W-B |
Heated oxygen sensor heater |
Ignition switch on (IG) |
9 to 14 V |
| HT1B (C33-62) - E1 (A32-1) |
LG - W-B |
Heated oxygen sensor heater |
Ignition switch on (IG) |
9 to 14 V |
| KNK1 (C33-78) - KNK2 (C33-57) |
R - G |
Knock sensor |
Engine speed maintained at 4,000 rpm after warming up engine |
Pulse generation (See waveform 5) |
| OCV- (C33-61) - E1 (A32-1) |
R - W-B |
Camshaft timing oil control valve |
Ignition switch on (IG) |
Pulse generation (See waveform 6) |
| EVP1 (C33-22) - E1 (A32-1) |
L - W-B |
EVAP VSV |
Ignition switch on (IG) |
9 to 14 V |
| STP (A32-38) - E1 (A32-1) |
G - W-B |
Stop light switch |
Brake pedal depressed |
9 to 14 V |
| STP (A32-38) - E1 (A32-1) |
G - W-B |
Stop light switch |
Brake pedal released |
Below 1.5 V |
| ST1- (A32-16) - E1 (A32-1) |
Y - W-B |
Stop light switch |
Brake pedal depressed |
Below 1.5 V |
| ST1- (A32-16) - E1 (A32-1) |
Y - W-B |
Stop light switch |
Brake pedal released |
9 to 14 V |
| W (A32-39) - E1 (A32-1) |
B - W-B |
MIL |
Ignition switch on (IG) (MIL goes off) |
Below 3.0 V |
| SPD (A32-37) - E1 (A32-1) |
V - W-B |
Speed signal from combination meter |
Vehicle speed of approximately 20 km/h (12 mph) |
Pulse generation (See waveform 7) |
| M+ (A32-2) - M- (A32-3) |
G - R |
Throttle actuator |
Idling with warm engine |
Pulse generation (See waveform 8) |
| FAN (C33-23) - E1 (A32-1) |
O - W-B |
FAN No .1 relay |
Ignition switch on (IG) |
9 to 14 V: When radiator fan not operates Below 1 V: When radiator fan operates Radiator fan operates according to engine coolant temperature and air conditioning operation |
| FAN2 (C33-5) - E1 (A32-1) |
W - W-B |
FAN No. 2 relay |
Ignition switch on (IG) |
9 to 14 V: ECT 94.5°C (202.1°F) or less; Fan motor low speed control Below 1 V: ECT 96°C (204.8°F) or more; Fan motor high speed control |
| ELS (A32-36) - E1 (A32-1) |
V - W-B |
Rear defogger switch |
Defogger ON |
9 to 14 V |
| ELS2 (A32-28) - E1 (A32-1) |
G - W-B |
Tail light switch |
Tail light ON |
9 to 14 V |
| CANH (A32-25) - E1 (A32-1) |
L - W-B |
Communication signal with other components |
Ignition switch on (IG) |
Pulse generation (See waveform 9) |
| CANL (A32-33) - E1 (A32-1) |
W - W-B |
Communication signal with other components |
Ignition switch on (IG) |
Pulse generation (See waveform 10) |
| TACH (A32-32) - E1 (A32-1) |
LG - W-B |
Engine revolution signal |
Idling |
Pulse generation (See waveform 11) |
| TC (A32-7) - E1 (A32-1) |
P - W-B |
Mode switch signal |
Ignition switch on (IG) |
9 to 14 V |
| * CAN+ (A32-34) - CAN- (A32-26) |
W - B |
Communication signal with transmission control ECU |
Ignition switch on (IG) |
Pulse generation (See waveform 12) |
| * NEO (C33-64) - E1 (A32-1) |
L - W-B |
Engine speed signal |
Idling |
Pulse generation (See waveform 13) |
- HINT:
- *: With Multi-mode Manual Transmission System
| WAVEFORM 1 |
![]() ![]() |
Igniter IGT signal (from ECM to igniter)
ECM Terminal Name
Between IGT1 (to IGT3) and E1
Tester Range
2 V/DIV, 20 msec/DIV
Condition
Idling
- HINT:
- The wavelength becomes shorter as engine rpm increases.
| WAVEFORM 2 |
![]() ![]() |
Camshaft position sensor
Crankshaft position sensor
ECM Terminal Name
(a) Between G1 and G-
(b) Between NE+ and NE-
Tester Range
5 V/DIV, 20 msec/DIV
Condition
Idling after engine warmed up
- HINT:
- The wavelength becomes shorter as engine rpm increases.
| WAVEFORM 3 |
![]() ![]() |
HO2S (sensor 1)
ECM Terminal Name
Between OX1A and E11
Tester Range
0.2 V/DIV, 200 msec/DIV
Condition
Engine RPM maintained at 2,500 rpm after engine warmed up
- HINT:
- In the Data List, the item HO2S B1 S1 shows the ECM input values of the HO2S (sensor 1).
| WAVEFORM 4 |
![]() ![]() |
HO2S (sensor 2)
ECM Terminal Name
Between OX1B and E12
Tester Range
0.2 V/DIV, 200 msec/DIV
Condition
Engine RPM maintained at 2,500 rpm after engine warmed up
- HINT:
- In the Data List, the item HO2S B1 S2 shows the ECM input values of the HO2S (sensor 2).
| WAVEFORM 5 |
![]() ![]() |
Knock sensor
ECM Terminal Name
Between KNK1 and KNK2
Tester Range
1 V/DIV, 1 msec/DIV
Condition
Engine RPM maintained at 2,500 rpm after engine warmed up
- HINT:
- The wavelength becomes shorter as engine rpm increases.
- The waveforms and amplitudes displayed differ slightly depending on the vehicle.
- The wavelength becomes shorter as engine rpm increases.
| WAVEFORM 6 |
![]() ![]() |
VVT OCV
ECM Terminal Name
Between OCV- and E1
Tester Range
5 V/DIV, 1 msec/DIV
Condition
Engine RPM maintained at 2,500 rpm after engine warmed up
- HINT:
- In the Data List, the item VVT OCV DUTY shows the duty ratio of voltage applied to the OCV (Click here).
| WAVEFORM 7 |
![]() ![]() |
Vehicle speed signal
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV, 20 msec/DIV
Condition
Vehicle speed of approximately 20 km/h (12 mph)
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
| WAVEFORM 8 |
![]() ![]() |
Throttle actuator
ECM Terminal Name
Between M+ and M-
Tester Range
20 V/DIV, 500 μsec/DIV
Condition
Idling after engine warmed up
- HINT:
- The duty ratio varies depending on the throttle actuator operation.
| WAVEFORM 9 |
![]() ![]() |
Communication signal
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV, 10 msec/DIV
Condition
Ignition switch on (IG)
| WAVEFORM 10 |
![]() ![]() |
Communication signal
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV, 10 msec/DIV
Condition
Ignition switch on (IG)
| WAVEFORM 11 |
![]() ![]() |
Engine speed signal
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV, 10 msec/DIV
Condition
Idling
- HINT:
- The wavelength becomes shorter as engine rpm increases.
| WAVEFORM 12 |
![]() ![]() |
Communication signal with transmission control ECU (for Multi-mode Manual Transmission System)
ECM Terminal Name
Between CAN+ and CAN-
Tester Range
1 V/DIV, 50 μs/DIV
Condition
Ignition switch on (IG)
| WAVEFORM 13 |
![]() ![]() |
Engine speed signal (for Multi-mode Manual Transmission System)
ECM Terminal Name
Between NEO and E1
Tester Range
5 V/DIV, 5 ms/DIV
Condition
Idling












