2005-2008 Yaris · Service Manual ENGINE

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Aug 2005


EURO-OBD (EUROPE)
When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.
Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:
FI02547E03
  1. The emission control system/components

  2. The power train control components (which affect vehicle emissions)

  3. A107926E01
    The computer
    In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL goes off automatically but the DTCs remain recorded in the ECM memory.
    To check DTCs, connect an intelligent tester or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.
    The scan tool displays DTCs, the freeze frame data and a variety of the engine data.
    The DTCs and freeze frame data can be erased with the scan tool (Click here).


M-OBD (EXCEPT EUROPEAN SPEC.)
When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.
OBD regulations require that the vehicle's on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in:
FI02547E03
  1. The emission control system/components

  2. The power train control components (which affect vehicle emissions)

  3. The computer
    In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL goes off automatically but the DTCs remain recorded in the ECM memory.


2-TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected again after the engine switch is turned off and then on (IG), the MIL illuminates.

DLC3 (Data Link Connector 3)
H100769E16
  1. The ECM uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

    Symbol
    Terminal No.
    Name
    Reference terminal
    Result
    Condition
    SIL
    7
    Bus "+" line
    5 - Signal ground
    Pulse generation
    During transmission
    CG
    4
    Chassis ground
    Body ground
    1Ω or less
    Always
    SG
    5
    Signal ground
    Body ground
    1Ω or less
    Always
    BAT
    16
    Battery positive
    Body ground
    9 to 14 V
    Always
    CANH
    6
    HIGH-lever CAN bus line
    CANL
    54 to 69 Ω
    Ignition switch off *
    CANH
    6
    HIGH-lever CAN bus line
    Body ground
    1 MΩ or higher
    Ignition switch off *
    CANH
    6
    HIGH-lever CAN bus line
    CG
    1 kΩ or higher
    Ignition switch off *
    CANL
    14
    LOW-lever CAN bus line
    Body ground
    1 MΩ or higher
    Ignition switch off *
    CANL
    14
    LOW-lever CAN bus line
    CG
    1 kΩ or higher
    Ignition switch off *

    NOTICE:
    *: Before measuring the resistance, leave the vehicle as is for at least 1 minutes and do not operate the ignition switch, any other switches or the doors.

    Connect the cable of the intelligent tester to the DLC3, turn the engine switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
    If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
    If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.


INSPECT BATTERY VOLTAGE
If the voltage is below 11 V, replace the battery before proceeding to the next step.

Standard voltage:
11 to 14 V


CHECK MIL
  1. Check that the MIL illuminates when turning the engine switch on (IG).
    If the MIL does not illuminate, there is a problem in the MIL circuit (Click here).

  2. When the engine is started, the MIL should go off.


ALL READINESS
For this vehicle, using the intelligent tester allows readiness codes corresponding to all DTCs to be read. When diagnosis (normal or malfunctioning) is complete, readiness codes are set.
← TERMINALS OF ECM (from Aug 2005)DTC CHECK / CLEAR (from Aug 2005) →