2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL RADIATOR DRAIN COCK

A147643
  1. Install the radiator drain cock onto the radiator assembly.


2. INSTALL RADIATOR RESERVE TANK HOSE GROMMET

A147642
  1. Install the 2 radiator reserve tank hose grommets onto the radiator assembly.


3. INSTALL RADIATOR SUPPORT CUSHION

A147641
  1. Install the 2 radiator support cushions onto the radiator assembly.


4. INSTALL FAN SHROUD

A147640
  1. Engage the 2 claws and install the fan shroud.


5. INSTALL WATER FILLER SUB-ASSEMBLY

  1. A147639
    Install the water filler sub-assembly with the clip.

  1. A147638
    Install the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the radiator reservoir tank hose to the water filler sub-assembly.


6. INSTALL RADIATOR ASSEMBLY

A147637
  1. Engage the 2 claws and install the radiator assembly onto the vehicle.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.

  1. A147635
    Connect the cooling fan motor connector and wire harness clamp.


7. INSTALL FAN SHROUD VENTILATION DUCT ASSEMBLY

A147636
  1. Engage the 4 claws and install the fan shroud ventilation duct assembly.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.


8. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY UPPER

A147634
  1. Install the radiator support sub-assembly upper with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. A147633
    Connect the horn assembly connector.


9. INSTALL HOOD LOCK ASSEMBLY

A108456
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. A108455
    Install the hood lock control cable assembly with the 2 clamps.


10. CONNECT NO. 2 RADIATOR HOSE

A147632
  1. Connect the No. 2 radiator hose with the clip.


11. CONNECT NO. 1 RADIATOR HOSE

A147631
  1. Connect the No. 1 radiator hose with the clip.


12. INSTALL AIR CLEANER ASSEMBLY

13. INSTALL FRONT BUMPER COVER

  1. B160102
    Install the 2 clips, the 2 spring nuts and the screw grommet.

  1. B160100
    Connect the 2 fog light connectors.

  1. Engage the 6 claws and install the front bumper cover.

  1. B160161
    Install the 7 clips.

  1. B160098
    Install the 2 screw grommets.

  1. Install the 5 screws and the 3 bolts.

  1. B160160E01
    Remove the protective tape.


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


15. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it is completely full.

    Capacity:
    5.0 liters (5.3 USqts, 4.4 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens.
      While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.


16. ADJUST HOOD LOCK ASSEMBLY

B106964
  1. Loosen the 3 bolts.

  1. Adjust the hood lock position so that the striker can enter it smoothly.

  1. Tighten the 3 bolts after the adjustment.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


17. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A147619E01
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.

← REMOVAL (from Nov 2006)ON-VEHICLE INSPECTION (from Aug 2005) →