2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2006

CAUTION:
Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans may automatically start if the engine coolant temperature is high or the air conditioning is on.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN ENGINE COOLANT

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, then drain the coolant.

    A147622E02


3. REMOVE FRONT BUMPER COVER

  1. B160160E01
    Apply protective tape as shown in the illustration.

  1. B160097
    Remove the 5 screws and the 3 bolts.

  1. Remove the 2 screw grommets.

  1. B160161
    Remove the 7 clips.

  1. B160099E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper cover.

  1. Disconnect the 2 fog light connectors.

  1. B160102
    Remove the 2 clips, the 2 spring nuts and the screw grommet.


4. REMOVE AIR CLEANER ASSEMBLY

5. DISCONNECT NO. 1 RADIATOR HOSE

A147631
  1. Loosen the clip and disconnect the No. 1 radiator hose.


6. DISCONNECT NO. 2 RADIATOR HOSE

A147632
  1. Loosen the clip and disconnect the No. 2 radiator hose.


7. REMOVE HOOD LOCK ASSEMBLY

A108455
  1. Separate the hood lock control cable assembly from the 2 clamps.

  1. A108456
    Remove the 3 bolts and remove the hood lock assembly.


8. REMOVE RADIATOR SUPPORT SUB-ASSEMBLY UPPER

A147633
  1. Disconnect the horn connector.

  1. A147634
    Remove the 4 bolts and remove the radiator support sub-assembly upper.


9. REMOVE FAN SHROUD VENTILATION DUCT ASSEMBLY

A147636
  1. Disengage the 4 claws and remove the fan shroud ventilation duct assembly.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.


10. REMOVE RADIATOR ASSEMBLY

A147635
  1. Separate the cooling fan motor connector and wire harness clamp.

  1. A147637
    Disengage the 2 claws and remove the radiator assembly from the vehicle.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.


11. REMOVE WATER FILLER SUB-ASSEMBLY

A147638
  1. Disconnect the radiator reservoir tank hose from the water filler sub-assembly.

  1. Remove the 2 bolts.

  1. A147639
    Loosen the clip and remove the water filler sub-assembly.


12. REMOVE FAN SHROUD

A147640
  1. Disengage the 2 claws and remove the fan shroud.


13. REMOVE RADIATOR SUPPORT CUSHION

A147641
  1. Remove the 2 radiator support cushions from the radiator assembly.


14. REMOVE RADIATOR RESERVE TANK HOSE GROMMET

A147642
  1. Remove the 2 radiator reserve tank hose grommets from the radiator assembly.


15. REMOVE RADIATOR DRAIN COCK

A147643
  1. Remove the radiator drain cock from the radiator assembly.

← ON-VEHICLE INSPECTION (from Nov 2006)INSTALLATION (from Nov 2006) →