2005-2008 Yaris · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Nov 2005

HINT:
In this section, the terms Cold and Hot refer to the temperature of the coils. Cold means approximately -10 to 50 °C (14 to 122 °F). Hot means approximately 50 to 100 °C (122 to 212 °F).


INSPECT IGNITION COIL AND SPARK TEST
  1. Check for DTCs.

    NOTICE:
    If a DTC is present, perform troubleshooting in accordance with the procedure for that DTC.

  1. Check whether sparks occur.

    1. Remove air cleaner cap assembly (Click here).

    2. Remove the 4 ignition coils (Click here).

    3. Using a 16 mm (0.63 in) plug wrench, remove the 4 spark plugs.

    4. Install the spark plug onto each ignition coil and connect the ignition coil connectors.

    5. Disconnect the 4 injector connectors.

    6. Ground the spark plugs.

    7. Check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Ground the spark plug when checking.
      2. Replace the ignition coil when it has been subjected to a physical impact.
      3. Do not crank the engine for more than 2 seconds.

  1. Perform the spark test in accordance with the following procedure.

    1. Check that the wire harness side connector of the ignition coil with igniter is securely connected.

      Result:
      Result
      Proceed to
      NG
      Connect securely
      OK
      Go to next step

    2. Perform a spark test on each ignition coil with igniter.

      1. Replace the ignition coil with igniter with a functioning one.
      2. Perform the spark test again.

      Result:
      Result
      Proceed to
      OK
      Replace ignition coil with igniter
      NG
      Go to next step

    3. Check the power supply to ignition coil with igniter.

      1. Turn the engine switch on (IG).
      2. Check that there is battery voltage at ignition coil positive (+) terminal.

      Result:
      Result
      Proceed to
      NG
      Check wiring between engine switch and ignition coil with igniter
      OK
      Go to next step

    4. Check the resistance of the camshaft position sensor.

      Standard resistance:
      Temperature
      Specified Condition
      Cold
      1,630 to 2,740 Ω
      Hot
      2,065 to 3,225 Ω

      Result:
      Result
      Proceed to
      NG
      Replace camshaft position sensor
      OK
      Go to next step

    5. Check the resistance of the crankshaft position sensor.

      Standard resistance:
      Temperature
      Specified Condition
      Cold
      1,630 to 2,740 Ω
      Hot
      2,065 to 3,225 Ω

      Result:
      Result
      Proceed to
      NG
      Replace crankshaft position sensor
      OK
      Go to next step

    6. Check the IGT signal from the ECM.

      Result:
      Result
      Proceed to
      NG
      Check ECM
      OK
      Repair wiring between ignition coil and ECM

  1. Connect the 4 injector connectors.

  1. Using a 16 mm (0.63 in) plug wrench, install the 4 spark plugs.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the 4 ignition coils (Click here).

  1. Install air cleaner cap assembly (Click here).


INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.

  1. I039522E11
    Check the electrode.

    1. Using a megaohmmeter, measure the insulation resistance.

      Standard resistance:
      Greater than 10 MΩ

      HINT:
      If a megaohmmeter is not available, perform the following simple inspection instead.

  1. Alternative inspection method.

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the 4 spark plugs.

    3. P003783E01
      Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

    4. Check the spark plug for any damage on its thread and insulator.
      If there is damage, replace the spark plug. If not, reinstall the spark plug.

      Recommended spark plug:
      Manufacturer
      Product
      DENSO
      K16R-U

    5. P003792E03
      Check the spark plug electrode gap.

      Maximum electrode gap for used spark plug:
      1.11 mm (0.044 in.)

      If the gap is greater than the maximum, replace the spark plug.

      Electrode gap for new spark plug:
      0.7 to 0.8 mm (0.028 to 0.031 in.)

      NOTICE:
      Bend only the base of the ground electrode when adjusting the gap of a new spark plug. Do not adjust the gap of a used plug.

    6. B062019
      Clean the spark plugs.
      If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

      Air pressure:
      588 kPa (6 kgf/cm2, 85 psi)

      Duration:
      20 seconds or less

      HINT:
      Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

← SYSTEM DIAGRAM (from Nov 2005)COMPONENTS (from Nov 2005) →