2005-2008 Yaris · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Nov 2006


INSPECT STARTER ASSEMBLY

NOTICE:
The following tests must be performed for no longer than 5 seconds to prevent the coil from burning out.

  1. Perform the pull-in test.

    1. Remove the nut and disconnect the lead wire from terminal C.

    2. A158854E01
      Connect the battery to the starter magnetic switch as shown in the illustration. Check that the clutch pinion gear is extended.
      If the result is not as specified, replace the magnet starter switch assembly.

  1. A158855E01
    Perform the hold-in test.

    1. Disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear remains extended.
      If the result is not as specified, replace the magnet starter switch assembly.

  1. A158856E01
    Check the operation.

    1. Disconnect the negative (-) lead from the switch body. Check that the clutch pinion gear returns.
      If the result is not as specified, replace the magnet starter switch assembly.

  1. Perform the no-load performance test.

    1. Connect the lead wire to terminal C. Make sure that the lead is not grounded.

      Torque:
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    2. Clamp the starter in a vise.

    3. A117813E01
      Connect the battery and an ammeter to the starter as shown in the illustration.

    4. Check that the starter rotates smoothly and steadily with the clutch pinion gear extended. Check that the ammeter reads the specified current.

      Standard current:
      Tester connection
      Condition
      Specified condition
      Positive battery terminal - Terminal 30 - Terminal 50
      11.5 V
      Below 90 A

      If the result is not as specified, replace the starter assembly.


INSPECT STARTER ARMATURE ASSEMBLY

  1. A104566E01
    Check the commutator for open circuits.

    1. Using an ohmmeter, check the resistance between the segments of the commutator.

      Standard resistance:
      Tester connection
      Specified condition
      Segment - Segment
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.

  1. A104565E01
    Check the commutator for ground.

    1. Using an ohmmeter, check the resistance between the commutator and the armature core.

      Standard resistance:
      Tester connection
      Specified condition
      Commutator - Armature core
      10 kΩ or higher

      If the result is not as specified, replace the starter armature assembly.

  1. Check the commutator surface for dirt and burnt.
    If the surface is dirty or burnt, restore it with sandpaper (No. 400) or a lathe.

  1. A158857
    Check the commutator for circle runout.

    1. Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum runout:
      0.05 mm (0.0020 in.)

      If the runout is greater than the maximum, replace the starter armature assembly.

  1. A158858
    Using vernier calipers, measure the commutator diameter.

    Standard diameter:
    28.0 mm (1.1024 in.)

    Minimum diameter:
    27.0 mm (1.0630 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. A158859
    Check that the undercut portion between the segments is free of foreign matter and measure its depth.

    Standard undercut depth:
    0.6 mm (0.0236 in.)

    Minimum undercut depth:
    0.2 mm (0.0079 in.)

    If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


INSPECT STARTER YOKE ASSEMBLY

  1. A158860E01
    Using an ohmmeter, check the resistance between terminal C and the field coil brush lead.

    Standard resistance:
    Tester connection
    Specified condition
    Terminal C - Brush lead
    Below 1 Ω

    If the result is not as specified, replace the starter yoke assembly.

  1. A158861E01
    Using an ohmmeter, check the resistance between the brush lead and the body.

    Standard resistance:
    Tester connection
    Specified condition
    Brush lead - Body
    10 kΩ or higher

    If the result is not as specified, replace the starter yoke assembly.


INSPECT BRUSH

  1. A037017
    Using vernier calipers, measure the brush length.

    Standard length:
    14 mm (0.5511 in.)

    Minimum length:
    9 mm (0.3543 in.)

    If the length is less than the minimum, replace the starter brush holder assembly and the starter armature assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A153747E01
    Using an ohmmeter, measure the resistance between the positive (+) and negative (-) brush holders.

    Standard resistance:
    Tester connection
    Specified condition
    Positive brush holder - Negative brush holder
    10 kΩ or higher

    If the result is not as specified, replace the starter brush holder assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

A158862E01
  1. Hold the starter clutch and rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    If necessary, replace the starter clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A033580
    Check the plunger.

    1. Push in the plunger and check that it returns quickly to its original position.
      If necessary, replace the magnet starter switch assembly.

  1. A156363E01
    Check the pull-in coil for open circuits.

    1. Using an ohmmeter, check the resistance between terminals 50 and C.

      Standard resistance:
      Tester connection
      Specified condition
      Terminal 50 - Terminal C
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  1. A156364E01
    Check whether the holding coil has an open circuit.

    1. Using an ohmmeter, check the resistance between terminal 50 and the switch body.

      Standard resistance:
      Tester connection
      Specified condition
      Terminal 50 - Body
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

← DISASSEMBLY (from Nov 2006)REASSEMBLY (from Nov 2006) →