2005-2008 Yaris · Service Manual ENGINE

Fuel Pump Control Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

When the engine is cranked, the ST (Starter) relay drive signal output from the STAR terminal of the ECM is input to the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates.
While the NE signal is input to the ECM with the engine running, the ECM turns the Tr1 on continuously.
A128482E01

WIRING DIAGRAM

A128487E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPD)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.

    OK:
    Fuel pump operating sound occurs.



OK
Go to step 8
NG


2. INSPECT MAIN BODY ECU (C/OPN RELAY INPUT VOLTAGE)
A116124E15
  1. Measure the voltage between the terminal of the main body ECU and the body ground when the ignition switch is on (IG) and off.

    Standard voltage:
    Tester Connections
    Ignition Switch Conditions
    Specified Conditions
    4B-11 - Body ground
    Off
    Below 1 V
    4F-4 - Body ground
    4B-11 - Body ground
    On (IG)
    9 to 14 V
    4F-4 - Body ground



OK
Go to step 4
NG


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY)
A112627E06
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the 4B and 4F main body ECU connectors.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    1B-4 - 4F-4
    Below 1 Ω
    1A-4 - 4B-11

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    4F-4 - Body ground
    10 kΩ or higher
    4B-11 - Body ground

  1. Reinstall the integration relay.

  1. Reconnect the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT

4. INSPECT MAIN BODY ECU (C/OPN RELAY)
A116124E19
  1. Remove the main body ECU.

  1. Connect the battery positive terminal to the 4D-1 terminal, and connect the battery negative terminal to the 4E-5 terminal.

  1. Check the C/OPN relay resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    4A-8 - 4B-11
    10 kΩ or higher
    Below 1 Ω
    (when battery voltage applied to terminals 4D-1 and 4E-5)

    HINT:
    The relay coil circuit between 4D-1 and 4E-5 is not through the IGN fuse.

  1. Reinstall the main body ECU.



NG
REPLACE MAIN BODY ECU
OK


5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
A115687E07
  1. Disconnect the 4E main body ECU connector.

  1. Disconnect the A21 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    4E-5 - FC (A21-7)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    FC (A21-7) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FUEL PUMP - BODY GROUND)
A116150E03
  1. Check the 4A harness and the connectors between the main body ECU and the fuel pump.

    1. Disconnect the 4A main body ECU connector.

    2. Disconnect the J5 fuel pump connector.

    3. Check the resistance.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      4A-8 - Fuel pump (J5-4)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connections
      Specified Conditions
      4A-8 - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the fuel pump connector.

  1. Check the harness and connector between the fuel pump and the body ground.

    1. Disconnect the J5 fuel pump connector.

    2. Check the resistance.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      Fuel pump (J5-5) - Body ground
      Below 1 Ω

    3. Reconnect the fuel pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FUEL PUMP
A095616E06
  1. Inspect fuel pump resistance.

    1. Measure the resistance between the fuel pump terminals.

      Standard resistance:
      0.2 to 3.0 Ω at 20°C (68°F)

  1. Inspect fuel pump operation.

    1. Apply battery voltage to the fuel pump terminals.

    2. Check that the fuel pump operates.

      NOTICE:
      1. This test must be done quickly (within 10 seconds) to prevent the coil from burning out.
      2. Keep the fuel pump as far away from the battery as possible.
      3. Always switch at the battery side.



NG
REPLACE FUEL PUMP
OK

REPLACE ECM

8. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is on (IG) and the engine starts.

    Standard:
    Ignition Switch Conditions
    Tester Display (Starter Signal)
    On (IG)
    OFF
    Engine Start
    ON



NG
REPAIR OR REPLACE STARTING SYSTEM
OK


9. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Read the value while cranking.

    OK:
    The value is the same as the actual engine speed and is displayed with no interruption on the tester.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR CIRCUIT
OK

REPLACE ECM


← VC Output Circuit (from Nov 2005)Cranking Holding Function Circuit (from Nov 2005) →