2005-2008 Yaris · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

When the ignition switch is turned on (IG), the battery voltage is applied to the IGSW terminal of the ECM. The input signal to the MREL terminal of the ECM causes a current to flow to the EFI relay coil, closing the EFI relay contacts and supplying power to terminals +B and +B1 of the ECM.

WIRING DIAGRAM

A122627E02

INSPECTION PROCEDURE


1. INSPECT INTEGRATION RELAY (INTEGRATION RELAY - BODY GROUND)

  1. A107914E06
    Remove the integration relay from the engine room relay block.

  1. Measure the voltage between the terminal of the integration relay and body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    Integration relay (1C-1) - Body ground
    9 to 14 V

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - BATTERY)
OK


2. INSPECT INTEGRATION RELAY (ECD RELAY AND IG2 RELAY)

  1. A107921E12
    Inspect the AM2 fuse and ECD fuse.
    1. Remove the AM2 fuse and ECD fuse.

    2. Check the fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the fuses.

  1. Inspect the relay.

    1. Check the relay resistance.

      Standard resistance:
      Tester Connections
      Specified Conditions
      1C-1 - 1B-4
      10 kΩ or higher
      Below 1 Ω
      (When battery voltage applied to terminals 1B-2 and 1B-3)
      1C-1 - 1A-8
      10 kΩ or higher
      Below 1 Ω
      (When battery voltage applied to terminals 1C-1 and 1A-7)



NG
REPLACE INTEGRATION RELAY
OK


3. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)

  1. A122632E01
    Remove the integration relay from the engine room relay block.

  1. Disconnect the A49 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    MREL (A49-44) - Integration relay (1A-7)
    Below 1 Ω
    +B (A49-42) - Integration relay (1A-8)
    +B1 (A49-1) - Integration relay (1A-8)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    MREL (A49-44) or Integration relay (1A-7) - Body ground
    10 kΩ or higher
    +B (A49-42) or Integration relay (1A-8) - Body ground
    +B1 (A49-1) or Integration relay (1A-8) - Body ground

  1. Reinstall the integration relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

  1. A122599E02
    Disconnect the A49 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    E1 (A49-2) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (IGSW TERMINAL VOLTAGE)

  1. A122599E03
    Disconnect the A49 ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of ECM connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    IGSW (A49-70) - E1 (A49-2)
    9 to 14 V

  1. Reconnect the ECM connector.



OK
REPLACE ECM
NG


6. INSPECT FUSE (IGN FUSE)

  1. A107935E06
    Remove the IGN fuse from the main body ECU.

  1. Check the fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the IGN fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


7. CHECK HARNESS AND CONNECTOR (ECM - INTEGRATION RELAY)

  1. A122632E02
    Remove the integration relay from the engine room relay block.

  1. Disconnect the A49 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    IGSW (A49-70) - Integration relay (1B-4)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    IGSW (A49-70) or Integration relay (1B-4) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the ECM connector.

    Result:
    Result
    Proceed To
    Out of normal range
    A
    Within normal range (with Entry and Start System)
    B
    Within normal range (without Entry and Start System)
    C



B
Go to step 8

C
Go to step 9
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

8. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - MAIN BODY ECU)

  1. A116136E02
    Remove the integration relay from the engine room relay block.

  1. Disconnect the D65 main body ECU connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    Integration relay (1B-2) - IG2D (D65-5)
    Below 1 Ω
    Integration relay (1B-3) - Body ground

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    Integration relay (1B-2) or IG2D (D65-5) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ENTRY AND START SYSTEM

9. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - IGNITION SWITCH)

  1. A116137E01
    Remove the integration relay from the engine room relay block.

  1. Disconnect the D8 ignition switch connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    Integration relay (1B-2) - IG2 (D8-6)
    Below 1 Ω
    Integration relay (1B-3) - Body ground

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    Integration relay (1B-2) or IG2 (D8-6) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

  1. A107906E03
    Remove the ignition switch assembly.

  1. Check the resistance between the terminals of the ignition switch.

    Standard resistance:
    Switch Positions
    Tester Connections
    Specified Conditions
    LOCK
    -
    10 kΩ or higher
    ACC
    2 - 4
    Below 1 Ω
    ON
    1 - 2 - 4
    5 - 6
    START
    1 - 3 - 4
    5 - 6 - 7

  1. Reinstall the ignition switch.



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)


← Pre-heating Control Circuit (from Nov 2005)VC Output Circuit (from Nov 2005) →