2005-2008 Yaris · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor while the ignition switch is on (engine running). The ECM also provides this power to the sensors through the VC output circuit.
A122653E01
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM

A122644E01

INSPECTION PROCEDURE


1. CHECK MIL CONDITION
  1. Check that Malfunction Indicator Lamp (MIL) illuminates when turning the ignition switch on (IG).

    OK:
    MIL illuminates



OK
SYSTEM OK
NG


2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and the tester on.

  1. Check the communication between the intelligent tester and ECM.

    Result:
    Result
    Proceed To
    Communication is possible
    A
    Communication is impossible
    B



A
GO TO MIL CIRCUIT
B


3. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the C58 throttle body connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL is illuminated
    A
    MIL is not illuminated
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY ASSEMBLY
B


4. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the A33 manifold absolute pressure sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL is illuminated
    A
    MIL is not illuminated
    B

  1. Reconnect the manifold absolute pressure sensor connector.



A
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
B


5. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the A20 accelerator pedal position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL is illuminated
    A
    MIL is not illuminated
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL POSITION SENSOR
B


6. CHECK MIL (FUEL PRESSURE SENSOR)
  1. Disconnect the C56 fuel pressure sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL is illuminated
    A
    MIL is not illuminated
    B

  1. Reconnect the fuel pressure sensor connector.



A
REPLACE FUEL PRESSURE SENSOR
B


7. CHECK HARNESS AND CONNECTOR (VC CIRCUIT)

  1. A122645E01
    Disconnect the C58 throttle body connector.

  1. Disconnect the A33 manifold absolute pressure sensor connector.

  1. Disconnect the A20 accelerator pedal connector.

  1. Disconnect the C56 fuel pressure sensor connector.

  1. Disconnect the A49 and C50 ECM connectors.

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VCS (C50-29) - Body ground
    10 k Ω or higher
    VVLU (C50-27) - Body ground
    VPIM (C50-30) - Body ground
    VCPA (A49-34) - Body ground
    VCP2 (A49-33) - Body ground

  1. Reconnect the throttle body connector, manifold absolute pressure sensor connector, accelerator pedal position sensor connector, and fuel pressure sensor connectors.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← ECM Power Source Circuit (from Nov 2005)Cranking Holding Function Circuit (from Nov 2005) →