Blower Motor Circuit
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
When the heater control (blower switch) is set to position 1 or higher, the contact of the HTR relay is closed, current flows to the blower motor, and the blower motor operates. The blower motor speed can be changed by exchanging the ground and the blower resistor circuit with the heater control (blower switch).WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT FUSE (GAUGE, HTR) |
Remove the GAUGE fuse from the main body ECU.
Remove the HTR fuse from the engine room R/B and J/B.
Measure the resistance.
Standard resistance: Tester Item
Specified Condition
GAUGE fuse
Below 1 Ω
HTR fuse
Below 1 Ω
Reinstall the GAUGE fuse.
Reinstall the HTR fuse.
|
|
||||
| OK | |
| 2. INSPECT HTR RELAY |
![]() ![]() |
Remove the HTR relay from the main body ECU.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
3 - 4
Below 1 Ω
3 - 5
10 kΩ or higher
3 - 4
10 kΩ or higher
(when battery voltage is applied to terminals 1 and 2)
3 - 5
Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)
Reinstall the HTR relay.
|
|
||||
| OK | |
| 3. INSPECT BLOWER MOTOR |
![]() ![]() |
Disconnect the E4 blower motor connector.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the blower motor operates smoothly.
- OK:
- The blower motor operates smoothly.
Measure the current.
- Standard current:
Tester Connection
Condition
Specified Condition
E4-1 (GND) - E4-2 (+B)
Blower motor operates
1 to 3 A
Reconnect the blower motor connector.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (HTR FUSE - MAIN BODY ECU) |
![]() ![]() |
Disconnect the 4L main body ECU connector.
Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
4L-1 - Body ground
Always
10 to 14 V
Reconnect the main body ECU connector.
|
|
||||
| OK | |
| 5. INSPECT MAIN BODY ECU |
![]() ![]() |
Remove the HTR relay from the main body ECU.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4F-7 - HTR-3
Below 1 Ω
4E-17 - HTR-4
Below 1 Ω
Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
HTR-5 - Body ground
Always
10 to 14 V
Reinstall the HTR relay.
Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
4Q-5 - Body ground
Ignition switch on (IG)
10 to 14 V
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEATER CONTROL (BLOWER SWITCH)) |
![]() ![]() |
Disconnect the E1 heater control (blower switch) connector.
Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E1-9 (LO) - Body ground
Ignition switch on (IG)
10 to 14 V
Reconnect the heater control connector.
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BLOWER MOTOR) |
![]() ![]() |
Disconnect the E4 blower motor connector.
Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E4-1 (+B) - Body ground
Ignition switch on (IG)
10 to 14 V
Reconnect the blower motor connector.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR) |
![]() ![]() |
Disconnect the E3 blower resistor connector.
Disconnect the E4 blower motor connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
E3-4 - E4-1
Below 1 Ω
Reconnect the blower resistor connector.
Reconnect the blower motor connector.
|
|
||||
| OK | |
| 9. INSPECT BLOWER RESISTOR |
![]() ![]() |
Remove the blower resistor.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
E3-4 - E3-1
3.12 to 3.60 Ω
E3-4 - E3-3
1.45 to 1.67 Ω
E3-4 - E3-2
0.52 to 0.60 Ω
Reinstall the blower resistor.
|
|
||||
| OK | |
| 10. INSPECT HEATER CONTROL (BLOWER SWITCH) |
![]() ![]() |
Remove the heater control (blower switch).
Measure the resistance.
- Standard resistance:
Switch Position
Tester Connection
Specified Condition
0
ALL - E1-5 (E)
10 kΩ or higher
1
E1-9 (LO) - E1-5 (E)
Below 1 Ω
1 - 2
E1-9 (LO) - E1-5 (E) - E1-7 (M1)
Below 1 Ω
2
E1-9 (LO) - E1-5 (E) - E1-7 (M1)
Below 1 Ω
2 -3
E1-9 (LO) - E1-5 (E) - E1-7 (M1) - E1-6 (M2)
Below 1 Ω
3
E1-9 (LO) - E1-5 (E) - E1-6 (M2)
Below 1 Ω
3 - 4
E1-9 (LO) - E1-5 (E) - E1-6 (M2) - E1-10(HI)
Below 1 Ω
4
E1-9 (LO) - E1-5 (E) - E1-10 (HI)
Below 1 Ω
Reinstall the heater control (blower switch).
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (HEATER CONTROL (BLOWER SWITCH) - BLOWER RESISTOR) |
Disconnect the E1 heater control (blower switch) connector.

Disconnect the E3 blower resistor connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
E1-5 (E) - E3-1
Below 1 Ω
E1-6 (M2) - E3-2
Below 1 Ω
E1-7 (M1) - E3-3
Below 1 Ω
E1-10 (HI) - E3-4
Below 1 Ω
Reconnect the heater control (blower switch) connector.
Reconnect the blower resistor connector.
|
|
||||
| OK | ||
| ||









