2005-2008 Yaris · Service Manual ENGINE

Cranking Holding Function Circuit

Circuit diagnosis · Vehicles built from Nov 2006

DESCRIPTION

The cranking holding control system keeps energizing the starter relay from when the ECM detects the starter signal (STSW signal) from the ignition switch or the main body ECU until the ECM performs a judgement of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC cut relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal.
Also, the ECM monitors the starter relay operating conditions based on the STA terminal voltage status.
A103821E16

WIRING DIAGRAM

A159154E01
A159155E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned on (IG) and the engine starts.

    Standard:
    Condition
    Starter Signal
    Ignition switch on (IG)
    OFF
    Engine start
    ON

Result:
Result
Proceed to
Outside standard range
A
Within standard range
B



B
Go to step 12
A


2. INSPECT ECM (STSW TERMINAL VOLTAGE)
A115671E87
  1. Disconnect the ECM connector.

  1. Depress the clutch pedal fully.

  1. Perform the cranking operation.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A21-14 (STSW) - Body ground
    Engine Start
    9 to 13 V

  1. Reconnect the ECM connector.

    Result:
    Result
    Proceed to
    Within standard range
    A
    Outside standard range (without entry and start system)
    B
    Outside standard range (with entry and start system)
    C

HINT:
DTCs related to the communication with other computers may be set due to this inspection. Clear those DTCs after the inspection.



B
Go to step 5

C
Go to step 6
A


3. INSPECT ECM (STAR TERMINAL OUTPUT VOLTAGE)
A159770E01
  1. Disconnect the clutch start switch connector.

  1. Perform the cranking operation.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A16-2 - Body ground
    Engine Start
    11 to 14 V

  1. Reconnect the clutch start switch connector.

    Result:
    Result
    Proceed to
    Within standard range
    A
    Outside standard range (without entry and start system)
    B
    Outside standard range (with entry and start system)
    C



B
Go to step 7

C
Go to step 8
A


4. INSPECT CLUTCH START SWITCH

  1. A159771E01
    Disconnect the clutch start switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    ON (pushed)
    Below 1 Ω
    1 - 2
    OFF (free)
    10 kΩ or higher

  1. Reconnect the clutch start switch connector.

Result:
Result
Proceed to
Outside standard range
A
Within standard range
B



B
Go to step 12
A

REPLACE CLUTCH START SWITCH

5. INSPECT IGNITION SWITCH
A107906E06
  1. Remove the ignition switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    -
    LOCK
    10 kΩ or higher
    2 - 4
    ACC
    Below 1 Ω
    1 - 2 - 4
    ON
    5 - 6
    1 - 3 - 4
    START
    5 - 6 - 7

  1. Reinstall the ignition switch.



NG
REPLACE IGNITION SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH - BATTERY)

6. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU)
A122540E03
  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D66-4 (STSW) - A21-14 (STSW)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D66-4 (STSW) or A21-14 (STSW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ENTRY AND START SYSTEM (Click here)

7. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - IGNITION SWITCH AND ECM)
A159772E01
  1. Disconnect the ignition switch connector.

  1. Disconnect the clutch start switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D8-7 (ST2) - A16-2
    Always
    Below 1 Ω
    C20-52 (STAR) - A16-2
    Always

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D8-7 (ST2) - Body ground
    Always
    10 kΩ or higher
    C20-52 (STAR) - Body ground
    Always

    HINT:
    The wire between the clutch start switch and the ignition switch has a diode (refer to the wiring diagram). The current flowing to the clutch start switch is rectified by the diode.

  1. Reconnect the ignition switch connector.

  1. Reconnect the clutch start switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

8. INSPECT ST CUT RELAY
A159773E01
  1. Remove the ST CUT relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Always
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall the ST CUT relay.



NG
REPLACE ST CUT RELAY
OK


9. INSPECT ST CUT RELAY (RELAY HOLDER TERMINAL VOLTAGE)
A122713E05
  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D67-1 - D67-2
    Ignition switch on (IG)
    11 to 14 V

  1. Reinstall the ST CUT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST CUT RELAY - IG2 RELAY)
OK


10. CHECK HARNESS AND CONNECTOR (ST CUT RELAY - ECM, MAIN BODY ECU AND CLUTCH START SWITCH)
A159774E01
  1. Remove the ST CUT relay.

  1. Disconnect the clutch start switch connector.

  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D67-3 - C20-52 (STAR)
    Always
    Below 1 Ω
    D67-3 - D66-14 (STR2)
    Always
    Below 1 Ω
    D66-3 (STR) - D67-5
    Always
    Below 1 Ω
    A16-2 - D67-5
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D67-3 - Body ground
    Always
    10 kΩ or higher
    D67-5 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the main body ECU connector.

  1. Reconnect the clutch start switch connector.

  1. Reinstall the ST CUT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT MAIN BODY ECU (CHECK FOR SHORT)
A122713E06
  1. Disconnect the C20 ECM connector.

  1. Remove the ST CUT relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D67-3 - Body ground
    Always
    10 kΩ or higher
    D67-5 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the ST CUT relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE ENTRY AND START SYSTEM (Click here)
OK

REPLACE ECM

12. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ECM - ST RELAY)
A159775E01
  1. Remove the ST relay from the engine room R/B and J/B.

  1. Disconnect the clutch start switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A16-1 - A21-48 (STA)
    Always
    Below 1 Ω
    A16-1 - 2 (ST relay)
    Always
    Below 1 Ω
    1 (ST relay) - Body ground
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A16-1 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the ST relay.

  1. Reconnect the clutch start switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


14. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK

REPAIR OR REPLACE STARTER CIRCUIT (STARTER - ST RELAY)


← Fuel Injector Circuit (from Nov 2006)MIL Circuit (from Nov 2006) →