2005-2008 Yaris · Service Manual ENGINE

Fuel Injector Circuit

Circuit diagnosis · Vehicles built from Nov 2006

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A159160E01

INSPECTION PROCEDURE


1. INSPECT POWER SOURCE CIRCUIT

  1. A157859E02
    Disconnect the fuel injector connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C4-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    C5-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    C6-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    C7-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Reconnect the fuel injector connector.



NG
Go to step 4
OK


2. INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
  1. Check the fuel injector injection and volume (Click here).



NG
REPLACE FUEL INJECTOR
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

  1. A106388E18
    Disconnect the ECM connector.

  1. Disconnect the fuel injector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C4-2 - C20-108 (#10)
    Always
    Below 1 Ω
    C5-2 - C20-107 (#20)
    Always
    Below 1 Ω
    C6-2 - C20-106 (#30)
    Always
    Below 1 Ω
    C7-2 - C20-105 (#40)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C4-2 or C20-108 (#10) - Body ground
    Always
    10 kΩ or higher
    C5-2 or C20-107 (#20) - Body ground
    Always
    10 kΩ or higher
    C6-2 or C20-106 (#30) - Body ground
    Always
    10 kΩ or higher
    C7-2 or C20-105 (#40) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FUEL INJECTOR

4. INSPECT FUSE (AM2 FUSE)

  1. A112606E03
    Remove the AM2 fuse.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AM2 fuse
    Always
    Below 1 Ω

  1. Reinstall the AM2 fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


5. INSPECT INTEGRATION RELAY (IG2 RELAY)

  1. A159776E03
    Remove the integration relay (IG2 relay) from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - 1B-4
    Always
    10 kΩ or higher
    1C-1 - 1B-4
    Battery voltage applied to terminals 1B-2 and 1B-3
    Below 1 Ω

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - FUEL INJECTOR)


← Fuel Pump Control Circuit (from Nov 2006)Cranking Holding Function Circuit (from Nov 2006) →